Stihl FS 40 Service Manual Download Page 16

Page: 16 / 82

Series 4144 Components FC, FS, KM

Engine

5.1

Removing and Installing

– Remove the drive tube,

9.1

– Remove the rewind starter,

6.2

Take out the screw (arrow).

– Remove the filter cover (1).

Take out the screw (arrow).

Pull boot (1) off the spark plug.

545RA025 TG

545RA026 TG

Pull the protective cap (1) off the
spark plug boot (2).

– Push the boot on to the spark

plug.

– Turn the machine over.

Take out the screws (arrows).

– Turn the machine over

Remove the shroud (1).

938RA087 TG

545RA027 TG

545RA028 TG

Disconnect the short circuit wire
(1) and ground wire (2).

Disconnect the tank vent hose (1)
from the filter housing (arrow).

Disconnect the fuel return hose
(2) and fuel suction hose (1) from
the stubs (arrows).

– Install new fuel hoses,

8.9.2

545RA029 TG

545RA030 TG

545RA031 TG

Summary of Contents for FS 40



















































































Search results

Summary of Contents for FS 40

Reviews:

Related manuals for FS 40

Brands by name

Popular brands

Stihl FS 40, Service Manual

Search results

Summary of Contents for FS 40

Reviews:

Related manuals for FS 40

Brands by name

Popular brands