43
ENGLISH
GB
3.5 Throttle cable
1. Install the throttle cable on the engine if not al-
ready installed. See the engine supplier’s man-
ual.
2. Pull up the cable under the support’s (5:E) up-
per section and over the screws in fig. 7.
3. Install the cable in the throttle. See fig. 11.
3.6 Cables
Pull up the cables under the cover under the sup-
port’s (5:E) upper section and over the screws in
fig. 7. Then install the ends into the relevant con-
trol as follows:
1. Install the cable ends into the relevant control.
The cable marked (
R
) must be installed into the
reverse control. See fig. 9.
2. Install the cable’s adjuster sleeves into the slots
in the handle. See fig. 10.
3. Slide the electric cable on the stop control’s flat
pin. See fig. 11.
3.7 Gear lever
Install the gear lever (1:U) as follows:
1. Insert the gear lever (12:U) through the oval
hole in the machine.
2. Install the washer (13:J) on the gear lever screw.
3. Press the gear lever’s ball into the lever socket.
4. Install the lock the (13:K) so that the gear lever
locks into the lever.
5. Install the washer and nut (13:L) and tighten.
3.8 Rotor
Install the outer rotors (14:N) and cutting discs
(14:O).
Note that the holes in shafts and sleeves must cor-
respond before the screws are installed.
Install the screws with the stated lengths according
to fig. 14.
3.9 Splash guards
Install the outer splash guards (15:M) with screws,
nuts and washers according to fig. 15.
4 DESCRIPTION
The rotary cultivator is driven by a four-stroke en-
gine and is intended for soil cultivation in private
gardens. The most important parts and controls of
the rotary cultivator are described below.
4.1 Reverse control (1:A)
The control is used to start the rotor for reverse
when the engine is running.
Control in idle mode (released): No drive.
Control depressed: The machine reverses.
4.2 Drive control (1:B)
The control consists of a loop, positioned between
the left and right handle.
The control is used to start the rotor for forward
motion when the engine is running.
Control in idle mode (downward): No drive.
Control pressed up: Forward drive.
4.3 Stop (1:C)
The stop control is located in the middle of the
throttle and has two positions as follows:
ON: The engine can be started and operated.
OFF: The engine stops and cannot be started.
4.4 Throttle (1:D)
The throttle controls the engine’s revs.
Idle: Control in the rear position.
Full throttle and start: Control in the front position.
4.5 Handle (1:E)
The handle has two handgrips that are used to op-
erate the machine over the area to be cultivated.
The handle can be adjusted as follows:
• Laterally (angle) by releasing the lever (1:J).
• Vertically by releasing the knobs (1:S).
4.6 Fuel cap (1:F)
Unscrew the fuel cap to fill with petrol. The fuel
cap must always be closed during operation.
4.7 Protective grille (1:H)
The protective grille must always be installed dur-
ing operation. There are surfaces that become ex-
tremely hot under the protective grille that risk
causing personal injury if touched.
4.8 Cover (1:I)
The cover protects cables and the handle adjust-
ment.
4.9 Oil filling (K)
Always check the oil level before start-
ing the engine.
Plug for oil filler and checking the oil level.
Summary of Contents for SILEX 82R2-H
