Stenner Pumps 100DH1 Installation And Maintenance Manual Download Page 5 | Manualshive

Page: 5 / 50

background image

US and Canada 800.683.2378, International 904.641.1666

Classic Series

5

SAFETY INFORMATION

continued

Warns about hazards that WILL or CAN cause minor personal

injury or property damage if ignored.

PLUMBING

Chemical feed pump installation must always adhere to your local plumbing codes
and requirements. Be sure installation does not constitute a cross connection. Check
local plumbing codes for guidelines.

NOTICE: Indicates special instructions or general mandatory action.

This metering pump is portable and designed to be removable from the plumbing
system without damage to the connections.

Before installing or servicing the pump, read the pump manual for all safety
information and complete instructions. The pump is designed for installation and
service by properly trained personnel.

Installation of product must adhere to all regulatory and compliance codes
applicable to the area.

This metering pump and its components have been tested for use with the following
chemicals: Sodium Hypochlorite (10-15%), Muriatic Acid (20-22 Baume, 31.5%
HCl), and Soda Ash.

Cette pompe de dosage et ses composants ont été testés pour leur compatibilité
avec les produits chimiques suivants : hypochlorite de sodium (10 à 15 %), acide
chlorhydrique (20 à 22 % Baume, 31,5 % HCl), et carbonate de sodium.

This metering pump is certified by WQA for use with Water and Sodium Hypochlorite
15%, when using Santoprene

®

tube material.

This is the safety alert symbol. When displayed in this manual or on the
equipment, look for one of the following signal words alerting you to the
potential for personal injury or property damage.

PUMP SUITABLE FOR USE OUTDOORS

when installed with a Stenner Rain Roof Part

No. MP90000.

Electrical installation should adhere to all national and local codes. Consult a
licensed professional for assistance with proper electrical installation.

Removing power from pool/spa recirculation pump must also remove power from pump.

The use of an auxiliary safety device (not supplied), such as a flow switch or sensor,
is recommended to prevent feed pump operation in the event of a recirculation
pump failure or if flow is not sensed.

Point of chemical injection should be beyond all pumps, filters, and heaters.

Suitable for indoor and outdoor use.

Adaptée à une utilisation aussi bien à l’intérieur qu’à l’extérieur.

SAVE THESE INSTRUCTIONS

«
...
3
4
5
6
7
...
»

Summary of Contents for 100DH1



















































Reviews:

No comments

Related manuals for 100DH1

Brand: GE Pages: 28

Brand: Davey Pages: 8

Brand: Davey Pages: 8

Brand: Davey Water Products Pages: 4

Brand: hajdu Pages: 136

Brand: York Pages: 90

Brand: P.Lindberg Pages: 54

Summit Pumper Vacuum

Brand: Alto Pages: 6

DSE-5 THRU DSE-120

Brand: A.O. Smith Pages: 24

Brand: clage Pages: 148

Brand: P.Lindberg Pages: 54

HOF14AFRQ 1F Series

Brand: Halsey Taylor Pages: 4

Brand: Western Shelter Systems Pages: 2

Brand: Barnes Pages: 27

Brand: A.O. Smith Pages: 28

Brand: A.O. Smith Pages: 36

Brand: TapFlo Pages: 69

FloJet 3426 Series

Brand: Xylem Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands