Stenner Pumps 100DH1 Installation And Maintenance Manual Download Page 21 | Manualshive

Page: 21 / 50

background image

US and Canada 800.683.2378, International 904.641.1666

Classic Series

21

INSTALLATION

continued

Trim Injection Fitting

Duckbill
Check Valve

Shut-Off Valve

1/4" or
1/2" FNPT
Reduction
Bushing

Typical Point of Injection

DO NOT use thread seal tape
on pump tube threads.

INSTALL DISCHARGE LINE TO PUMP HEAD AND INJECTION POINT

1.

Make a secure finger tight connection on the discharge fitting of the pump head as
instructed in Install Suction Line instructions.

DO NOT use thread seal tape on pump tube connections.

HAZARDOUS PRESSURE: Shut off water or circulation system

and bleed off any system pressure.

Locate a point of injection beyond all pumps and filters or as determined by
the application.

2.

A 1/4" or 1/2" Female NPT (FNPT) connection is required for installing the injection
fitting. If there is no FNPT fitting available, provide one by either tapping the pipe or
installing FNPT pipe tee fitting.

3.

Wrap the Male NPT (MNPT) end of injection fitting with 2 or 3 turns of thread seal
tape. If necessary, trim the injection fitting quill as required to inject product directly
into flow of water.

More on next page

«
...
19
20
21
22
23
...
»

Summary of Contents for 100DH1



















































Reviews:

No comments

Related manuals for 100DH1

Brand: A.O. Smith Pages: 64

Brand: A.O. Smith Pages: 4

Brand: A.O. Smith Pages: 4

Brand: A.O. Smith Pages: 4

120 through 250 Series

Brand: A.O. Smith Pages: 74

Elmo Rietschle V-VC 40

Brand: Gardner Denver Pages: 32

Brand: Goodman Pages: 16

HYDROMATIC G2HX

Brand: Pentair Pages: 12

Brand: Raypak Pages: 40

Brand: OilGear Pages: 31

Brand: Rinnai Pages: 66

MULTI-HE Series

Brand: salmson Pages: 44

AJ 4 Plus 100/57 AUT

Brand: T.I.P. Pages: 20

Brand: HARNITEK Pages: 28

Brand: INOXPA Pages: 19

Brand: SHG Pages: 32

1 EPBH 9.2-11 T-AVS

Brand: EBARA Pages: 16

Brand: Calpeda Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands