Stenner Pumps 100DH1 Installation And Maintenance Manual Download Page 35 | Manualshive

Page: 35 / 50

background image

US and Canada 800.683.2378, International 904.641.1666

Classic Series

35

CLEANING THE POINT OF INJECTION –
SAFETY INFORMATION

NOTICE: Indicates special instructions or general mandatory action.

Pumps rated 25 psi maximum are installed with an injection fitting and pumps rated
100 psi maximum are installed with a duckbill check valve. Both allow the extension
tip to be installed in the center of the pipe directly in the flow of water to help reduce
deposit accumulation.

Warns about hazards that CAN cause death, serious

personal injury, or property damage if ignored.

This is the safety alert symbol. When displayed in this manual or on the
equipment, look for one of the following signal words alerting you to the
potential for personal injury or property damage.

HAZARDOUS PRESSURE/CHEMICAL EXPOSURE

Use caution and bleed off all resident system pressure prior to attempting service
or installation.

Use caution when disconnecting discharge line from pump. Discharge line may be
under pressure. Discharge line may contain chemical.

To reduce risk of exposure, the use of proper personal protective equipment is
mandatory when working on or near chemical metering pumps.

Injection Fitting

Duckbill

Areas that may clog

Check

Valve Body

Duckbill Check Valve

«
...
33
34
35
36
37
...
»

Summary of Contents for 100DH1



















































Reviews:

No comments

Related manuals for 100DH1

Brand: Samsung Pages: 27

Brand: Danfoss Pages: 34

Brand: Danfoss Pages: 52

Brand: Danfoss Pages: 38

Brand: Gardena Pages: 17

Q HEAT R Series

Brand: CANVAC Pages: 88

Summit Pumper Vacuum

Brand: Alto Pages: 6

PULSAR Shadow Series

Brand: Pulsafeeder Pages: 46

Brand: Daikin Pages: 40

Brand: OmarLift Pages: 28

SiFire EN 100/200-205-45 E

Brand: Wilo Pages: 108

DrainPress 3200/24 Set

Brand: T.I.P. Pages: 68

AirSite GreenMaster-HP 3-12/12

Brand: Nibe Pages: 104

Brand: TOHATSU Pages: 99

Brand: Binks Pages: 40

Brand: salmson Pages: 40

Water Quality System EQHP-TWIN 108SP

Brand: Bunn Pages: 2

Brand: Carrier Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands