Stenner Pumps 100DH1 Installation And Maintenance Manual Download Page 47

Page: 47 / 50

US and Canada 800.683.2378, International 904.641.1666

Classic Series

PUMP TUBES

NOTE: Confirm chemical compatibility with the chemical resistance guide in the catalog.

PUMP TUBE

Includes ferrules 1/4"

DESCRIPTION

2-PK

5-PK

#1 Santoprene

Tube

UCCP201 MCCP201

#2 Santoprene

Tube

UCCP202 MCCP202

#3 Santoprene

Tube

UCCP203 MCCP203

#4 Santoprene

Tube

UCCP204 MCCP204

#5 Santoprene

Tube

UCCP205 MCCP205

#7 Santoprene

Tube

UCCP207 MCCP207

(excludes Classic 100 or 170)

#1 Versilon

Tube

UCTYG01 MCTYG01

#2 Versilon

Tube

UCTYG02 MCTYG02

#3 Versilon

Tube

UCTYG03 MCTYG03

#4 Versilon

Tube

UCTYG04 MCTYG04

#5 Versilon

Tube

UCTYG05 MCTYG05

PUMP TUBE & DUCKBILL

Includes ferrules 1/4"

DESCRIPTION

2-PK

#1 Santoprene

Tube & Duckbill

UCCIFD

#2 Santoprene

Tube & Duckbill

UCCP2FD

#7 Santoprene

Tube & Duckbill

UCCP7FD

(excludes Classic 100 or 170)

#1 Versilon

Tube & Duckbill

UCTY1FD

#2 Versilon

Tube & Duckbill

UCTY2FD

PUMP TUBE

EUROPE

Includes ferrules 6 mm

DESCRIPTION

2-PK

5-PK

#1 Santoprene

Tube

UCCP21CE MCCP21CE

#2 Santoprene

Tube

UCCP21CE MCCP21CE

#3 Santoprene

Tube

UCCP23CE MCCP23CE

#4 Santoprene

Tube

UCCP24CE MCCP24CE

#5 Santoprene

Tube

UCCP25CE MCCP25CE

#7 Santoprene

Tube

UCCP27CE MCCP27CE

(excludes Classic 100 or 170)

#1 Versilon

Tube

UCTY1CE

MCTY1CE

#2 Versilon

Tube

UCTY2CE

MCTY2CE

#3 Versilon

Tube

UCTY3CE

MCTY3CE

#4 Versilon

Tube

UCTY4CE

MCTY4CE

#5 Versilon

Tube

UCTY5CE

MCTY5CE

PUMP TUBE & DUCKBILL

EUROPE

Includes ferrules 6 mm

DESCRIPTION

2-PK

#1 Santoprene

Tube & Duckbill

UC1FDCE

#2 Santoprene

Tube & Duckbill

UC2FDCE

#7 Santoprene

Tube & Duckbill

UC7FDCE

(excludes Classic 100 or 170)

#1 Versilon

Tube & Duckbill

UCTY1DCE

#2 Versilon

Tube & Duckbill

UCTY2DCE

Tube number located on fitting

Refer to the

FLOW RATE OUTPUT

chart

to match the pump with the correct tube

Summary of Contents for 100DH1



















































Search results

Summary of Contents for 100DH1

Reviews:

Related manuals for 100DH1

Brands by name

Popular brands

Stenner Pumps 100DH1, Installation And Maintenance Manual

Search results

Summary of Contents for 100DH1

Reviews:

Related manuals for 100DH1

Brands by name

Popular brands