STEMME S12 Maintenance Manual Download Page 46 | Manualshive

Page: 46 / 290

background image

DOCUMENT NUMBER:

L500-912.820 ISSUE JUL 20, 2016

AMENDMENT: 00

DATE: --

CHAPTER-

PAGE 3-12

MAINTENANCE MANUAL STEMME S12

• In the liquid cooling system, the combined function of the expansion reservoir and refill

container was split up in two separate containers, with the expansion reservoir located

above the engine and the refill container on the left side of the fire-wall.

• The ignition unit is installed above of the engine slightly behind the original ROTAX-position.
• The throttle levers on the carburetors have been slightly modified (modification does not

affect the throttle rigging of the original engine) and additional springs have been installed

(pulling towards full-power position) to compensate for friction due to the long control

cables between cockpit and engine bay.

Engine performance data of the ROTAX 914 F2/S1 are identical to those of the ROTAX 914 F.

ENGINE PERFORMANCE DATA
Max. T/O power.

84.5 kW at 5800 RPM

113.2 hp

Max. continuous power.

73.4 kW at 5500 RPM

98.4 hp

Engine reduction gear ratio

i = 2.4286

Max. propeller

2650 RPM

3.4.2

LUBRICATION SYSTEM

SYSTEM DESCRIPTION

Refer to »Maintenance Manual (Heavy Maintenance) for ROTAX Engine Types ROTAX 912 and 914

Series«, section 79.

The ROTAX 914 is equipped with a dry-sump pressure lubrication system. The pumps are part of

the engine. It was necessary to modify the routing of the oil pipes between oil pump and turbo-

charger. Oil is returned from the crankcase to the oil tank by compression blow-by pressure, and

from the turbocharger via the secondary oil pump (scavenge pump).

The oil tank is standard from ROTAX. It is installed behind the fire-wall on the LH side of the

fuselage frame. The oil filler cap is below a service access in the upper center fuselage fairing.

Oil is taken in flexible pipes from the oil tank through the fire wall to the engine bay. Any flexible

oil lines in the engine compartment are shrouded by fire protective sleeves.

The oil cooler is installed on the RH side of the fuselage frame and supplied with air from the RH

cowl flap.

«
...
44
45
46
47
48
...
»

Summary of Contents for S12



































































































































































































































































































Reviews:

No comments

Related manuals for S12

GIPPSAERO GA8-TC 320

Brand: Mahindra Pages: 148

Metroliner III SA227-BC

Brand: RAZBAM Pages: 93

Oldtimer XXL-59

Brand: aero-naut Pages: 8

FAA-STC SA10232SC

Brand: Forced Aeromotive Technologies Pages: 11

fun series 30" Crack Wing

Brand: Twisted Hobbys Pages: 42

Mini Warbirds Rare Bear

Brand: skyangel Pages: 8

ARCHER II PA-28-181

Brand: Piper Aircraft Corporation Pages: 117

Brand: COBHAM Pages: 126

Brand: Fresh Breeze Pages: 20

Brand: Ecotop Pages: 32

Brand: Opale-Parmodels Pages: 11

Brand: P&M Aviation Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands