Stel 607510000L, Manual

Page: 131 / 144

131
THOR 103
COD. 6909500060
STEL s.r.l. – Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail: stel @ stelgroup.it
http: www.stelgroup.it
12.0 SERVICE
12.1 INTRODUCTION
THIS SECTION DESRIBES BASIC MAINTENANCE PROCEDURES PERFORMABLE BY
OPERATING PERSONNEL.NO OTHER ADJUSTMENTS OR REPAIRS ARE TO BE AT-
TEMPTED BY OTHER THAN PROPERLY TRAINED PERSONEEL.
WARNING
Disconnect primary power at the source before dissasembling or torch leads.
Frequently review the important safety precautions at the front of this Manual. Be sure
the operator is equipped with proper gloves,clothing, eye and ear potection.make sure
no part of the operator ’ s body comes into contact with the work - piece while the torch is
actived.
CAUTION
Sparks from the cutting process can cause damage to coated, painted, and other surfaces
such as glass, plastic and metal.
NOTE
Handle torch leads with care and protect them from damage.
12.2 GENERAL TORCH MAINTENUACE
A. Cleanin Torch
Even if precautions are taken to use only clean air with a torch, eventually the inside of
the torch be comes coated with residue.This buildup can affect the pilot arc initiation
and the overall cut quality of the torch.
WARNINGS
Disconnect primary power to the system before dissasembling the torch or torch leads.
DO NOT touch any internal torch parts while the AC indicator light of the power supply
is ON.
The inside of the torch should be cleaned with electrical contact cleaner usign a cotton
swab or soft wet rag.In severe cases, the torch can be removed from the leads and
cleaned more thoroughly by pouring electrical cantact cleaner into the torch and blo-
wing it through with compressed air.
CAUTION
Dry th etorch thoroughly before reinstalling.
12.3 COMMON OPERATING FAULTS
Common Operating faults
The following lists the more common cuting faults and possible causes:
1. Insufficient penetration
ENGLISH
TECHNICAL
DESCRIPTION
131
THOR 103
COD. 6909500060
STEL s.r.l. – Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail: stel @ stelgroup.it
http: www.stelgroup.it
12.0 SERVICE
12.1 INTRODUCTION
THIS SECTION DESRIBES BASIC MAINTENANCE PROCEDURES PERFORMABLE BY
OPERATING PERSONNEL.NO OTHER ADJUSTMENTS OR REPAIRS ARE TO BE AT-
TEMPTED BY OTHER THAN PROPERLY TRAINED PERSONEEL.
WARNING
Disconnect primary power at the source before dissasembling or torch leads.
Frequently review the important safety precautions at the front of this Manual. Be sure
the operator is equipped with proper gloves,clothing, eye and ear potection.make sure
no part of the operator ’ s body comes into contact with the work - piece while the torch is
actived.
CAUTION
Sparks from the cutting process can cause damage to coated, painted, and other surfaces
such as glass, plastic and metal.
NOTE
Handle torch leads with care and protect them from damage.
12.2 GENERAL TORCH MAINTENUACE
A. Cleanin Torch
Even if precautions are taken to use only clean air with a torch, eventually the inside of
the torch be comes coated with residue.This buildup can affect the pilot arc initiation
and the overall cut quality of the torch.
WARNINGS
Disconnect primary power to the system before dissasembling the torch or torch leads.
DO NOT touch any internal torch parts while the AC indicator light of the power supply
is ON.
The inside of the torch should be cleaned with electrical contact cleaner usign a cotton
swab or soft wet rag.In severe cases, the torch can be removed from the leads and
cleaned more thoroughly by pouring electrical cantact cleaner into the torch and blo-
wing it through with compressed air.
CAUTION
Dry th etorch thoroughly before reinstalling.
12.3 COMMON OPERATING FAULTS
Common Operating faults
The following lists the more common cuting faults and possible causes:
1. Insufficient penetration
ENGLISH
TECHNICAL
DESCRIPTION