6939500000
18
Switch off the machine, turning the line switch to
“OFF” position.
Screw the current supply pipe and the nozzle back
on.
Regulate the friction of the wire feeder (a more
accurate regulation will be possible after a few
tests).
7)Press the Select Mode button (ref.7) to select the
desider mode, indicated by the lighting of the
corresponding LED (ref. 3,4,5,6): The following
mode are available:
MIG 2T :
in this function the arc start when the wire
goes in contact with the piece. When you press the
torch button the wire start come out and it stops
when you leave the button.
MIG 4T :
when you press the torch button the gas
comes out ( pre gas ). When you leave the button
the wire start come out, and goes in contact with
the piece and the arc start. Pushing again the
button the arc stops and the gas continue flowing
until the torch button is pressed. When you leave
the button start the post time pre setted.
SPOT WELDING :
this function works like MIG 2T
but is possible regulate the arc on time from 0,1
sec to 10 sec.
MULTI SPOT :
in this function is possible regulate
the ARC ON time and also the ARC OFF time.
Pressing
and
holding
the
torch
button
automatically is managed the ARC ON time and
ARC OFF time.
Now, if you want to proceed with manual
welding act as described hereinafter, otherwise
see the section “PREPARATION FOR MIG
WELDING IN SYNERGIC MODE”
8) Regulate the wire speed using the encoder
A/W.Sp.
(ref.13).
9) Regulate the voltage using the encoder
V/SET
(ref.12).
WARNING
PREPARING FOR MIG
WELDING WITHOUT GAS
To use a special cored wire that allows welding
without the use of gas, proceed as follows:
1) Check the position of the polarity changing
cable, opening the side door. Read the
paragraph “ REVERSE POLARITY”.
2) Connect the earth cable to the socket of
the machine. Positive polarity ( + ) Red.
3) Connect the torch coupling to the
centralised euro
socket of the machine.
Negative polarity ( - ) Black.
Now proceed as in the instructions in the
paragraph "PREPARING FOR MIG WELDING
WITH GAS".
PREPARATION FOR MIG
WELDING IN SYNERGIC
MODE
1) respect the indications given previously
concerning primary connection and installation until
the point 7.
2) Press the button
SIN/MAN
(ref.8) .
3) Using the button ↑ (ref.10) ↓ (ref.11) or the
encoder V/SET (ref.12) choose the desired
program and press the button
SELECT
(ref.8) to
access to the welding regulation screen.
APPROCH SPEED REGULATION
(START SPEED)
Press the button
SETUP
(ref.11) to go in the MIG
START PARAMETERS SETTING page.
For setting the value of START SPEED regulate
the encoder
V/SET
(ref.12). The START SPEED
value vary from 15 to 135 % of the welding wire
speed set up.
IGNITION SLOPE TIME REGULATION
(START TIME)
Press the button
SETUP
(ref.11) to go in the MIG
START PARAMETERS SETTING page.
Press the button SELECT (rif.8) to select the
START TIME.
For setting the START TIME regulate the encoder
V/SET
(ref.12). The START TIME value vary from
0,1 to 2 seconds.
START
SPEED
AND
START
TIME
FUNCTIONING ( 2T-4T NO ALLUMINIUM )
WA RNING
AVVERTENZA
AVERTISSEMENT
WA RNUNG
ADVERTENCIA
PRIMA DI INIZIARE LA SALDATURA
CHIUDERE IL PORTELLO
TO OPERATE CLOSE THIS PANEL
AVANT D’UTILISER LE GENERATEUR, IL
FAUT FERMER CE PANNEAU
VOR DEM SCHWEISSEN DEN DECKEL
SCHLIESSEN
PARA UTILIZAR LA MAQUINA, CIERRE ESTE
PANEL
WA RNING
AVVERTENZA
AVERTISSEMENT
WA RNUNG
ADVERTENCIA
