Steinbach 012140 Instruction Manual Download

Page: 9 / 52

Page 8 of 50

You can use the optional styrofoam wedges of us. These are

then stuck round with a force of glue to the floor insulation

along the pelvic wall. Alternatively, you can also make the fur-

row of sand. Regardless how to make the groove, you now have

on the floor insulation and the fillet a swimming fleece apply

because otherwise the bottom of the pool liner insulation re-

moves the plasticizers, the film becomes brittle and thereby

significantly reduces the lifetime.

Put the liner at the center of the pool site inside the pool wall. Extend

it evenly until the seam line reaches the base of the pool. Drape the

pool liner over pool wall. There should be an overlap of 8 cm of the

pool wall height. (See diagram 15)
Hold the overlap in place with clips. (See diagram 16).
Note: With the liner in position, fold the remaining liner material

evenly by dividing this excessive liner uniformly along entire perime-

ter but not fold on one point. (See diagram 17).

IMPORTANT:

If the dimension of the PVC liner is smaller than the

steel wall, do not stretch or force the PVC! Stop the assembly imme-

diately and call custom service for assistance.
3. Fill the pool with 1 or 2 cm of water and enter the pool to smooth

out the liner against the pool wall. (See diagram 18).

ASSEMBLING THE TOP RAILS

Remove the clips one at a time whilst applying the top rails. (See di-

agram 19, A: Top Plastic Rail).
Slide the rail connectors into one end of a top rail (see diagram 20),

then connect another top rail and continue around the pool until all

top rails are joined together (see diagram 20). Keep the same 1.5

cm gap as the bottom rails.
Do not cut the excess overlap off the pool liner wall, if you cut the

overlap, it will make the next pool installation difficult. do not tape the

overlap to the top rail also, it will cause difficultly when fix the top

rails.

INSTALLING THE TOP METAL PIECES

Hook the top metal pieces over the top of the rails (see diagram 21).

The first metal piece should be placed on top of and in the middle of

the steel wall joint.
Install the 8 top metal pieces in correspondence with the bottom

metal pieces installed in the above diagram 5. (See diagram 21

INSTALLING THE TOP PLATFORMS

Install the 8 top platforms starting from the steel wall joint as shown

in diagram 22.
NOTE: Adjust the distance between the two metal pieces if neces-

sary to accommodate for the top platforms.
NOTE: Make sure that you place the longer side of the top platform

facing out and the shorter side facing inside the pool.
Line up the screw holes and lightly fasten with the bolts provided in

the package. (See diagram 23).
NOTE: Repeat these steps for all 8 top platforms and make sure

they are all sitting properly before finally tightening all the nuts.

FIXING THE BOTTOM JOINT PROTECTOR

Fix the bottom joint protector to the vertical supports, using the

ST4.2x13 screws (No.16) as shown in diagram 24.

INSTALLING THE VERTICAL SUPPORTS

The first vertical support should be placed over the joint of the steel

wall as shown in diagram 25.
Fix the vertical support onto the metal pieces as shown in diagram

26. Line up the bolts.

04 Top Metal Piece

13 Pool Vertical Support

14 M4x10 Bolt

17 Bottom Metal Piece
NOTE: The vertical support must be straight before installing the

bolts.

INSTALLING THE UPPER JOINT PROTECTORS

1. Hook the upper joint protector over the inside edge of the top rail

and pull it down to fasten it outside edge. (See diagram 27, A: 01.

UpperJoint Protector16)

FILLING THE POOL - STEP 1

When assembly is finished and before you start to fix the skimmer

and the inlet connector kit to the pool, fill the pool with 5 or 6 cm of

water below the position of the inlet connector kit. (See diagram

28)WARNING! Never permanently install the skimmer or the inlet

connector kit before the water is within a few centimeters of them,

because the liner has to be properly taut with the pressure of the wa-

ter.

INSTALLING THE INLET CONNECTOR KIT AND SKIMMER

Unpack your inlet connector kit and skimmer box from the carton.

Carefully read the instructions bellow before you start to mount them

onto the pool wall. (See diagram 29)

No. Name

Quantity

Hose attachment

Cover

Basket

Skimmer Housing

Weir

Gsket

Face Plate

Screw (ST5x24)

Outlet connector

Inlet connector kit

Hose clamp

Teflon Tape

Plug

Step1: Assembling the inlet connector kit

When filling the pool, once the level of water has reached 5 or 6cm

away from the inlet hole, install the inlet as follows:
Cut the liner to accommodate the inlet using a knife, and fold the cut

edges over the wall. See diagram 30, A: Round for the inlet, B: Tef-

lon tape, C: coat here, D: Pool wall, E: Stop water flowing, F: Allow

water flowing)
Screw the Inlet connector kit to the pool wall. Make sure the Teflon

tape is coated onto the threading of the inlet connector fist. (See di-

agram 30)
Screw the remaining parts of the inlet connector kit into position.

(See diagram 30)

Step 2: Assembling the Skimmer

(See diagram 31, A: Pool outside, B: Pool inside, diagramm 32, A:

Teflon Tape)

Stahlwandpool Set Nuovo de Luxe II

| 20

_V1

Page 9 of 50

Replace the lip seal on the skimmer cutout on. Make sure that the

flange holes fit!
From outside the pool, place the gasket and skimmer housing

against the pool wall in line with the hole.
From inside the pool, place the faceplate and gasket against the

pool wall in line with the hole. Push the screws carefully through pool

liner but do not securely tighten them until all the screws are in

place. Ensure that the housing and inside faceplate are correctly

aligned and tighten the screws into position but do not over tighten

as you may damage the screws and / or the pool wall and liner. En-

sure that the gasket is not pinched or damaged.

WARNING:

Do not create multiple holes as this will void your war-

ranty and cause damage to the pool liner. Carefully trim off any pro-

truding part of the liner inside the connections after installation.
Place the basket into the skimmer housing and fix the cover . Coat

the Teflon tape to the threading of the outlet connector and then

connect it to the skimmer housing.
Clip the weir to the front of the pool skimmer housing if not already

assembled.
Make sure the skimmer is sealed to the pool wall and no water is

leaking.
Connect the filtration system to the pool. Follow the filtration sys-

tem’s instructions for assembly requirements before operating.

WARNING!

Never permanently install the skimmer or the inlet be-

fore the water arrives to within a few centimeters of them, because

the liner has to be properly taut with the pressure of the water.

WARNING!

Cutting more liner than necessary will damage and void

the pool liner, so please trim with extra care.Caution! Do not damage

any part of the inside of the skimmer box and Inlet and outlet con-

nections with the knife.

FILLING THE POOL - STEP 2

Before you fill the pool with water, thoroughly check to see if there

are any loose screws, holes or tears in the liner. Continue to fill the

pool until water reaches half way into the skimmer box opening. The

pool is full when water reaches about 15 cm from the top of the pool

wall. (See diagram 36)

WARNING!

To avoid collapse, never leave the pool without water.

POOL MAINTENANCE

Warning:

If you do not adhere to the maintenance guidelines cov-

ered herein, your health might be at risk, especially that of your chil-

dren.
NOTE: The pump is used to circulate the water and to filter small

particles to keep your water clean. In order to keep you pool water

clean and hygienic you must add chemicals.
Always keep your pool clean and apply the correct pool chemicals.

Unsanitary water is a serious health hazard.
Maintain pool pH level between 77,2 to 7.6
The pH is altered by, among other factors such as water tempera-

ture, frequency of bathing, dirt and other environmental influences.
Ask your dealer’s advice if you want to modify your filtration system.
Clean the PVC liner regularly with non-abrasive brushes or a venture

vacuum cleaner.
Throughout the season the water filtration system must run long

enough each day to clean the entire volume of water in the pool.
Check the filter cartridge regularly and replace dirty cartridges.
Regularly check the screws, bolts and all the metal parts for rust.

Replace if necessary.
If it rains, check that the water level is not higher than the specified

level. If water exceeds the specified levels, drain the pool to the

specified level.

Cover the pool when not in use.

ATTENTION:

Do not leave the drained pool outside.

ATTENTION:

The use of a kit swimming pool implies the respect of

the safety instructions described in the manual of maintenance and

use.

WINTERIZATION

If you do not want to dismantle the pool in winter, please ob-

serve the following instructions:
Damage caused by freezing are not covered by warranty!

Do not drain away all of the pool water, if you do so, the pool may

collapse.
Drain the water 10 cm below the inlet valve on the pool wall. You

can use a pump or a garden hose. (See diagram 37)
Treat the pool water with a suitable chemical product.
Remove the filtration system from the pool and drain away any water

inside the filtration system.You can leave the inlets/outlets attached

to the pool. Store the filtration system in a dry place. Preferably in

the original carton.
7. Also remove any other pool accessories and store them in a dry

and cool place.
8. Protect the pool with the pool cover.

Stahlwandpool Set Nuovo de Luxe II

| 20

_V1