background image

Folio™ Desk Frame, Desk Frame and End Panel

& Desk Frame with Back Panel

If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at

888.STEELCASE

 (888.783.3522)

for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico, 
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com

©

 

2014 Steelcase Inc. 

Grand Rapids, MI 49501 
U.S.A.  
Printed in U.S.A.

®

Page 1 of 14

939500540 Rev F

 

CAUTION

FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN
PROPERTY DAMAGE OR PERSONAL
INJURY.

Read the entire Assembly Direction
before beginning installation or assembly.
Building construction varies greatly and
is outside Steelcase's control. The
Building's Engineer of Record is
responsible for the design of studs,
backing, reinforcement, supporting
members etc. which the units are
attached to and must verify the adequacy
of the mounting hardware. These
instructions and any hardware provided
by Steelcase are for convenience only
and are not an indication of what may be
required by your local Code.

The building owner or designated agent
is responsible for verifying that the
installation is in compliance with all local
Codes and regulations.

Desk Frame

with Back Panel

(with or without Doors)

Desk Frame

with End Panel

Desk Frame

CLAMP

WOOD BLOCK

3/8" SPADE BIT

MASKING TAPE

(Used to help prevent
any possible chipping

while drilling)

Summary of Contents for Folio Desk Frame















Reviews: