stayer SC210W, Operating Instructions Manual

Page: 20 / 20

ENGLISH
17
17
Set the protractor (34) at 0°.
Set the desired distance using the scale on the table top (18).
Tighten the lock knob (35).
Set the guide fence so that the guide profile (37) is parallel to
the saw blade.
Instructions for use
Check whether the guide fence has been mounted correctly
(when using the machine in the table saw position).
Switch on the machine before the workpiece makes contact
with the saw blade.
Do not exert pressure on the saw blade. Allow the machine
enough time to cut the workpiece.
If the saw blade comes to a standstill or decelerates, the machine
is being overloaded. Immediately stop sawing and let the motor
cool down by leaving the machine running idle for some time.
Switching on and off (fig. A1 & A2)
The machine has been fitted with a voltage protection:
this protection prevents the machine from unintendedly being
switched on while the machine is connected to the mains
voltage.
When using the machine in the cut-off saw position:
To switch on the machine press the on/off switch (1).
To switch the tool off, release the on/off switch.
When using the machine in the table saw position:
To switch the machine on, set the on/off switch (15) to ‘I’.
To switch the machine off, set the on/off switch to ‘0’.
Ripping (fig. F & H)
Ripping cuts are performed with the machine set up in the table
saw position. While ripping, the workpiece is guided along the
guide fence and sawn through longitudinally.
Set the guide fence (17) for parallel guiding when ripping and
set the guide profile (37).
Switch on the machine.
Securely hold the workpiece and guide it along the saw blade
keeping it pressed against the guide fence.
In the final stage use the push stick to keep your hands well
clear from the saw blade.
Switch the machine off as soon as the cut is completed.
Always use the push stick to cut extremely small
workpieces.
Sawing straight cross-cuts (fig. F, G & J)
Straight cross-cuts are performed with the machine set up in the
cut-off saw position or in the table saw position. While sawing
straight cross-cuts when using the machine in the cut-off saw
position the workpiece is placed against the fence and sawn
through transversely. While performing the same cut when using
the machine in the table saw position the workpiece is placed
against the guide fence.
For sawing straight cross-cuts in the cut-off saw position,
proceed as follows:
Keep the workpiece pressed to the table and the guide fence (13).
Switch on the machine.
Depress the head with equal force to allow the saw blade to
cut through the workpiece and enter the table slot
Switch the machine off as soon as the cut is completed.
Only raise the head after the saw blade has come to a
complete standstill.
For sawing straight cross-cuts in the table saw position,
proceed as follows:
Set the guide fence (17) for sawing straight cross-cuts.
Place the workpiece lengthwise against the profile and set the
guide profile (37).
Switch on the machine.
Securely hold the workpiece and guide it along the saw blade
keeping it pressed against the guide fence.
Switch the machine off as soon as the cut is completed.
Sawing mitre cuts (fig. F, G & K)
Mitre cuts are performed with the machine set up in the cut-off
saw position or in the table saw position. While sawing mitre
cuts when using the machine in the cut-off saw position the
workpiece is placed against the fence and sawn through
transversely at an angle. While performing the same cut when
using the machine in the table saw position the workpiece is
placed against the guide fence.
For sawing mitre cuts in the cut-off saw position, proceed as
follows:
Set the mitre angle.
Proceed as described for sawing straight cross-cuts in the
cut-off saw position.
For sawing mitre cuts in the table saw position, proceed as follows:
Set the guide fence (17) for sawing mitre cuts.
Proceed as described for sawing straight cross-cuts in the
table saw position, starting in point 2.
Sawing bevel cuts (fig. L)
Bevel cuts are performed with the machine set up in the cuf-off
saw position. While sawing bevel cuts, the workpiece is placed
against the fence and sawn through at an inclination.
Set the bevel angle.
Proceed as described for sawing straight cross-cuts in the
cut-off position.
Sawing compound mitre cuts (fig. F & M)
Compound mitre cuts are performed with the machine set up in
the cuf-off saw position. While sawing compound mitre cuts,
the workpiece is placed against the fence and sawn through in a
combined mitre and bevel cut.
Set the mitre angle.
Set the bevel angle.
Proceed as described for sawing straight cross-cuts in the
cut-off position.
Mounting and adjusting the table extenders (fig. N)
Using the table extenders you can support long workpieces.
The table extenders can be mounted both to the left and to the
right of the machine.
Insert on each side a table extender (41) into the openings in
the base of the machine as shown.
Dust extraction (fig. O)
The dust extraction outlet together with an external vacuum
cleaner takes care of the dust extraction of the working surface.
Place the adapter (42) on the dust extraction connection (5).
Connect a vacuum cleaner to the machine.
Lubrication (fig. E2)
From time to time, apply a drop of oil to the thread of the lock
screw (28).
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●