Star Trac E-STe Work Instructions Download Page 45 | Manualshive

Page: 45 / 53

background image

46

620-7925 Rev x1

Step 33.

Plug  the  DC  power  cable  from  the  base  neck
into  either  one  of  the  DC  connectors  on  new
center console board.  Then plug the DC power
cable from the PVS neck into the other DC con-
nectors on same center console board.

Step 34.

Plug the data interface cable coming from the
PVS neck into the center console board.

Step 35.

Plug the video cable coming from the PVS neck
into the center console board.

Step 36.

Plug the audio cable coming from the PVS neck
into the center console board.

«
...
43
44
45
46
47
...
»

Summary of Contents for E-STe






















































Reviews:

No comments

Related manuals for E-STe

Brand: idiag Pages: 10

Brand: M-Audio Pages: 70

Brand: M-Audio Pages: 16

Brand: HYDRA-RIB Pages: 25

XC-Classic 2000

Brand: Abilica Pages: 49

Brand: Total Gym Pages: 14

Club Seated Leg Curl Series

Brand: LifeFitness Pages: 17

Brand: Domyos Pages: 4

Brand: Skandika Fitness Pages: 52

Brand: Bodykey Pages: 10

Brand: Freemotion Pages: 12

Total Gym Shaper

Brand: Fitness Quest Pages: 7

Brand: Sune Technology Pages: 22

Brand: Franklin Pages: 22

Brand: SHIFTER Pages: 2

Brand: Titanium Strength Pages: 9

Brand: 100FIT Pages: 19

Personal series

Brand: AbCoaster Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands