manualshive.com logo in svg

Stanhope-Seta 30000-0, Installation, Operating And Maintenance Instructions

Share
Download
Stanhope-Seta 30000-0 Installation, Operating And Maintenance Instructions Download Page 23

Pubn No: 30000H0K 

 

 

 

 

 

Switch ON 

 

 

 

 

 

 

….. switch the Setaflash Series 
3 ON at the ON/OFF Power 
Switch on the rear of the 
instrument. 

 

 

 

 

 

 

 

Version N.NN
 

 

The display will show the 
software version ….. 

N.NN = software version 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Calibrate Mode
Please wait … 

 

….. then change to show the 
current status. 

Release the Set Temperature 

 and Set Timer 

Buttons. 

Release 

The Sample Cup will start to 
heat up to 55°C 

as measured 

by the Setaflash Series 3 
Flash Point Tester.

 

When the instrument measures 
the Sample Cup temperature as 
55°C the display will countdown 
from 300 seconds while the 
temperature stabilises. 

Calibrate Mode
Please wait 300 

°C 

           

 55

°C

 

Issue K 

10 Jun 2007 

23

Summary of Contents for 30000-0













































Reviews:

No comments

Brands by name

Popular brands

Load more brands