manualshive.com logo in svg

St. Jude Medical QUANTIEN, Instructions For Use Manual

Share
Download
St. Jude Medical QUANTIEN Instructions For Use Manual Download Page 72

 

68 

 

 

To change batteries proceed as follows: 
1.

 

Remove the screws at the back of the remote control. 

2.

 

Open the case and remove the plastic holder and remove the batteries. 

CAUTION: Be careful with the circuit board. 

3.

 

Replace the batteries with new ones. Make sure the polarity is correct. Polarity markings are 

located at the bottom of the casing. 

CAUTION: Do not reverse the poles. 

Replace the plastic holder and close the case. Secure it with the screw. 

System Backup Battery 

The internal system backup battery is recharged by leaving the QUANTIEN™ measurement 
system turned on. The battery is not intended to be replaced. 

Disposal 

NOTE: To avoid environmental damage and/or personal injury, handling and disposal of 
batteries and electronic equipment shall be done in accordance with applicable local, 
state and federal laws and regulations. 

Cleaning 

CAUTION: Do not immerse in liquid: Do not use the QUANTIEN™ measurement 
system if it has been immersed in liquid. 

1.

 

Turn OFF the unit and disconnect the mains power cable. 

2.

 

After each patient, clean the exterior with a moist tissue, using regular cleaning agents, or if 
necessary, alcohol, and wipe dry. 

3.

 

Reconnect the main power cable. 

4.

 

Press ON/OFF switch to ON. 

WARNING: 

 

Make sure that every part of the unit is dry before reconnecting to the power 
supply. 

 

Do not use the QUANTIEN measurement system if liquid is suspected to 

have penetrated the enclosure or the power supply unit. This can cause the 

user or patient to be exposed to electric shock. Contact St. Jude Medical 
representatives or technical support for further instructions. 

Preventative Maintenance Schedule 

It is recommended that the scheduled preventative maintenance of the QUANTIEN™ 
measurement system should be performed with an interval not exceeding 12 months. The list 
below shows the operations needed to ensure the electrical safety and measurement accuracy of 
the QUANTIEN measurement system. These operations are preferably performed in the order 
according to the list below. Instructions for performing these operations are found in the 
instructions in the remainder of this chapter. 
The measurements should always be carried out by a qualified technician. 
Ageing of cabling and multi-use pressure transducers can affect performance of measurements. It 

State: Released

  

Date: 2019.03.06 22:30 GMT

Summary of Contents for QUANTIEN





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands