SST Automation GT200-HT-RS User Manual Download Page 6

Page: 6 / 52

WWW.SSTCOMM.COM

2 Quick Start Guide

The following example introduces the use method of the Gateway.

2.1 Configuration of Gateway Parameters

2.1.1 Pre-configured Settings

1. Turn gateway’s configuration bit of DIP switch(refer to chapter 3.3.1) to “ON”;

2. Connect the Gateway’s RS-232/USB interface and the serial port of the computer with a serial cable, wiring

methods see chapter 3.4.3 of this manual;

3. Power on the gateway, the LED display shows “CF”, indicates that the gateway is in the configuration mode.

Run the SST-HT-CFG to start the gateway configuration.

2.1.2 Software Configuration

1. Run the SST-HT-CFG software installed on your computer.

2. Click “Fieldbus” in the tree view on the left, the configuration table is shown on the right as below:

Summary of Contents for GT200-HT-RS





















































Search results

Summary of Contents for GT200-HT-RS

Reviews:

Related manuals for GT200-HT-RS

Brands by name

Popular brands

SST Automation GT200-HT-RS, User Manual

Search results

Summary of Contents for GT200-HT-RS

Reviews:

Related manuals for GT200-HT-RS

Brands by name

Popular brands