SST Automation GT200-HT-RS User Manual Download Page 12

Page: 12 / 52

WWW.SSTCOMM.COM

3.2 Indicators

Indicator location

Indicator

State

State Description

Row 1

Blinking

Serial port data sending

OFF

No data is sending

Blinking

Serial port data receiving

OFF

No data is receiving

Row 2

Blinking

HART Bus data sending

OFF

No data is sending

Blinking

HART Bus data receiving

OFF

No data is receiving

3.3 DIP Switch/Button

3.3.1 DIP Switch

The DIP switch is located at the bottom of product, bit 1 is the debug bit and bit 2 is the configuration bit.

Debugging (bit 1)

Configuration (bit 2)

Description

Off

Run Mode

Off

Configuration Mode

Off

Debug Mode

Configuration Mode

Note:

①

After re-configuring the switch, you have to restart the GT200-HT-RS to make the settings take

effect! (Power off then Power On)

②

Set to the debug mode, it will be compulsory to appoint RS-485 interface as communication

interface, RS-232/USB interface as debugging interface.

③

Configuration interface uses the RS-232/USB interface.

Off

On 1 2

Summary of Contents for GT200-HT-RS





















































Search results

Summary of Contents for GT200-HT-RS

Reviews:

Related manuals for GT200-HT-RS

Brands by name

Popular brands

SST Automation GT200-HT-RS, User Manual

Search results

Summary of Contents for GT200-HT-RS

Reviews:

Related manuals for GT200-HT-RS

Brands by name

Popular brands