background image

IMPORTANT SAFETY INSTRUCTIONS

Inside you will find many helpful hints on how to use and maintain your air conditioner
properly. Just a little preventive care on your part can save you a great deal of time 
and money over the life of your air conditioner. You'll find many answers to common 
problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting 
Tips first, you may not need to call for service at all.

   

To prevent injury to the user or other people and property damage, the following 
instructions must be followed. Incorrect operation due to ignoring of instructions may 
cause harm or damage. The seriousness is classified by the following indications.

This symbol indicates the possibility of death or serious injury.

Always do this.

Never do this.

CAUTION

This symbol indicates the possibility of injury or damage to property.

WARNING

ARNING

W

Plug in power plug 
properly.

Do not modify power cord length or share the 
outlet with other appliances. 

Always ensure proper 
grounding.

Unplug the unit immediately if strange sound, 
smell or smoke is emitting from unit.

Keep firearms away.

If there was a gas leak from another appliance, ventilate 
the room thoroughly before operating the unit.

   Otherwise, it may cause electric
   shock or fire due to excess heat 
   generation.

  It may cause electric shock or fire due to heat generation.

  Incorrect grounding may cause 
  electric shock.

It may cause electric shock.

  It may cause fire.

  It may cause explosion, fire and, burns.

  It may cause electric shock or fire
  due to heat generation.

  It may cause electric shock.

  It may cause failure of machine
  or electric shock.

  It may cause fire and electric 
  shock.

  It may cause electric shock or fire.
  If the power cord is damaged, it must be replaced by the 
  manufacturer or an authorised service centre or a similarly 
  qualified per son in order to avoid a hazard.

This is not beneficial to one's health.

  Incorrect installation may cause 
  fire and electric shock.

It may cause fire and electric

It may cause fire and electric shock.

  It may cause failure and electric shock.

Do not operate or stop the
unit by inserting or 
removing the power plug.

Do not operate with wet
hands or in damp 
environment.

Do not allow water to run
into electric parts.

Do not use the socket if it is
loose or damaged.

Keep power cord away from 
heat sources.

Do not damage or use an unspecified power 
cord.

Do not direct airflow directly at room occupants

Always install circuit 
breaker and a dedicated
power circuit.

Do not open the unit 

during operation.

Do not use the power cord near flammable gas
or combustibles, such as gasoline, benzene,
thinner, etc.

It may cause an explosion or fire.

Do not disassemble or modify the unit.

!

!

!

!

!

!

!

!

READ THIS MANUAL

1

Summary of Contents for WA-10FMS1



















Reviews: