manualshive.com logo in svg

SPRT SP-T8, User Manual

Share
Download
SPRT SP-T8 User Manual Download Page 88

 

88

than one line in vertical, the following processing is 
performed only on the line in question: 

The printin

①

g area width is extended to the right up to one 

line in vertical. In this case, printing does not exceed the 
printable area. 

If the printing area width cannot be extended by one line in 

②

vertical, the left margin is reduced to accommodate one line 
in vertical. 
[Reference] 

GS 

,

 GS #

 

GS :                                                                                                     

[Name] Start/end macro definition 
[Format]        ASCII     GS    : 

Hex            1D        3A 
Decimal      29        58 

[Description] Starts or ends macro definition. 
[Notes]  

Macro definition starts when this command is received 

　

 

during normal operation. Macro definition ends when this   
command is received during macro definition. 

When 

　

GS ^ 

is received during macro definition, the printer 

ends macro definition and clears the definition. 

Macro is not defined when the power is turned on.

　

 

The defined contents of the macro are not cleared by 

　

ESC 

@

. Therefore, 

ESC @ 

can be included in the contents of the 

macro definition. 

Summary of Contents for SP-T8






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands