manualshive.com logo in svg

SPRT SP-T8, User Manual

Share
Download
SPRT SP-T8 User Manual Download Page 82

 

82

GS $ nL nH                                                                                       

[Name] Set absolute vertical print position in page mode 
[Format]                ASCII      GS      $      nL      nH 

Hex    1D   24  nL   nH 
Decimal 29   36  nL   nH 

[Range] 0 

nL 

255, 0 

nH 

255

　

　

　

　

 

[Description]  

Sets the absolute vertical print starting position for buffer 

　

 

character data in page mode. 

This command sets the absolute print position to [( nL + nH 

　

256) 

(vertical or horizontal motion unit)] inches.

　

　

 

[Notes]  

This command is effectiv

　

e only in page mode. 

If the [( nL + nH 

256) 

(vertical or horizontal motion unit)] 

　

　

　

exceeds the specified printing area, this command is ignored. 

The horizontal starting buffer position does not move.

　

 

The reference starting position is that specifi

　

ed by 

ESC T

. 

This command operates as follows, depending on the 

　

starting position of the printing area specified by 

ESC T

: 

When the starting position is set to the upper left or lower 

①

right, this command sets the absolute position in the vertical 
direction. 

When the starting position is set to the upper right or lower 

②

left, this command sets the absolute position in the horizontal 
direction. 

The horizontal and vertical motion unit are specified by 

　

GS 

Summary of Contents for SP-T8






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands