12
Solution: check the connection of the electronic system to 4 cables of the
controller, check whether the wire is not loose or damaged and whether the
sequence of the 4-core connection is appropriate.
The electronic board shows: error E02! Anti riot
E02: the voltage on the engine’s cable is not detected by the controller.
Solution: check whether the connections of endings of positive and
negative cable on the engine and on the controller are securely connected.
The electronic board shows: error E03! No speed signal
E03: the controller does not detect the feedback signal of speed when the
engine is operating.
Solution: check whether the photoelectric sensor is adapted to the opening
in the engine and shield; check whether the photoelectric sensor is not
damaged and whether cable endings in the controller and photoelectric
sensor are securely connected.
The electronic board shows: error E05
E05: signals that the engine load is too big and that the value of the rated
current was exceeded.
Solution: check whether the engine is not damaged or replace the engine.
The electronic board shows: safety lock off
Removed safety key: the electronic system does not detect the signal of
the safety key.
Solution: check whether the magnetron is not damaged, whether the
magnetron is in correct position, and whether the magnet was put in place.
OTHER PROBLEMS AND SOLUTION METHODS
No displays of the electronic board:
Check whether the plug of the supply cable is connected to the socket,
whether the power supply switch is switched on and whether the fuse in
the controller is not burnt.
Check whether the 4-core cable for the electronic system to the controller
is connected.
Check whether the controller is connected.
No display or chaotic display of the heartbeat frequency sensor in the
holder:
Check whether the connection is secure.
Check whether the hand is in contact with the sensor.
Wash your hands with water and keep them moist.
The engine cannot start
Check whether all the connection cables are connected.
Observe the error signal in the electronic system.
The touch screen is not sensitive:
Check whether the touchscreen is not moist.
Check whether your hands are not sweaty.
It is not possible to receive WiFi signals, the equipment is not connected to
the network.
The IP address is usually automatically assigned, but you can assign the
IP address manually.
The method of setting the static IP address is as follows:
1. In the main interface click the settings button and go to the WiFi settings.
2. After clicking on the requested name of the network setting a dialogue
frame with place for entering the password will appear.
3. In the dialogue frame enter the correct network password and click
“Connect”. The message “Connected” should appear next to the selected
network on the list of networks.
4. Press and hold the name of the network connection until the dialogue
frame appears. Select the position “Static IP".
5. In the next dialogue frame move the scroll bar at the position Static IP.
Enter your IP address and the gate in the IP address bar (if you do not
know your IP address and the gate, check the IP address and the gate in
your phone or on your computer). Click Save after entering the data in
correct way.
No power supply
Check the fuses (found in the
controller under the engine’s housing).
Check the supply socket (plug in any other equipment and make sure
that the power outlet is functioning properly).
Check the supply cable (you may need the electrician’s help).
USAGE
Placing the treadmill, scope of usage
The treadmill should be placed in a dry place, and not exposed to the
stream of water and moisture. The treadmill should be placed on a clean
and flat surface. Placing the treadmill on an uneven surface can cause
damage to its system. You cannot place the treadmill on a carpeted or
floor covering.
The treadmill is intended for indoor use only.
This equipment may not be exposed to an aerosol spray or oxygen.
Moreover, it may not be placed in areas where gas is used due to
possible sparks coming out of the engine.
The treadmill should be placed at a distance of about 2 m from walls and
objects that may be dangerous to the user.
The security area of 2 x 1 m must be left behind the exercise machine.
Treadmill exercises replace walks and jogging. The treadmill is intended
for home use only and it is not designed for any therapeutic or
rehabilitation purposes.
The device is not designed for a long-term operation or any commercial
activities.
Your body position
Get onto the treadmill belt; you can rest your hands on the handrails. While
doing your exercises, you should have your back straight. On the treadmill,
you can perform exercises which replace walks or jogging (see figure).
Any injuries may result from incorrect or
intensive training.
NOTE: You should keep your hands away
from moving parts.
Shaping your muscles
To shape your muscles during exercises, you should increase the
resistance substantially. This will bring about the increased muscle tension
and it may mean that you will not be able to train for as long as you want.
If you would also like to exercise your fitness, you should change your
training programme. You should exercise practising the following stages:
warm-up stage, proper training stage and
relaxation stage. However, at the end of your
training, you should increase the resistance,
so that you can enhance the workout of your leg muscles. You should also
reduce your speed, so that the pulse remains at the indicated level.
Weight loss, Training sessions
An important factor here is the effort you put into your exercises. The longer
and harder you train, the more calories you will burn. It will be a success to
obtain the same efficiency as for fitness training.
It is recommended to perform your exercises 3-4 times per week
– for
approx.: 30 minutes.
Intensive training, which helps you to lose your weight, should be carried
out more frequently, for at least approx.: 45-50 minutes