Spedo 2600 Operator'S Manual Download Page 26

Page: 26 / 51

26 |

S p e d o 2 6 0 0 O p e r a t o r M a n u a l

S p e d o U K L t d

Spedo 2600 Pinless Cutter Operator Manual

Fig 3.2 Summary of Controls – Pushbuttons

Spedo

SP2300

Select Mode:

Standard

Enhanced

POWER

OFF

OPERATOR PANEL

POWER SWITCH

EMERGENCY STOP SWITCH

FINE TUNE BUTTON

SET-UP BUTTONS

MANUAL/CONTINUOUS BUTTONS

LINE ADVANCE BUTTON

IN-FEED BUTTON

MANUAL BLADE BUTTON

CONTINUOUS BUTTON

STOP BUTTON

START BUTTON

POWER SWITCH

Set this rocker switch to

ON to apply power to the

machine

EMERGENCY STOP SWITCH

Hit this button to stop the cutter

immediately

TRIM OFFSET BUTTONS

Press the TRIM FORWARD

and TRIM BACKWARD buttons
to offset the leading edge of the

paper web.

LINE ADVANCE

Press this button

momentarily – the form

advances one line.

Press and hold this button –

the form is moved

continuously in the line

increments.

Press the STOP & LINE

ADVANCE buttons

simultaneously – the form

moves back one line

IN-FEED

Press this button to

advance the leading edge

of the web from the

datum mark on the tractor

flaps to the cutter blade.

Press the STOP & IN-

FEED buttons

simultaneously to set the

pause.

MANUAL BLADE

Press this button for a

single cross cut.
Press the STOP

button & this button to

select the NO CUT

option.

The BLADE button

illuminates when

active.

CONTINUOUS

Press this button

for continuous

operation of the

cutter before the

START button has

been depressed.
This is a latching

button which

illuminates when

active.

STOP

1. In Continuous mode this button interrupts
the operation.

2. If side trimming only is being performed
(No-Cut operation), press this button to stop
the operation.

START

Once the Mode of

Operation has been

set-up, press this

button to activate the

process.

OPERATOR PANEL

Summary of Contents for 2600




















































Search results

Summary of Contents for 2600

Reviews:

Brands by name

Popular brands

Spedo 2600, Operator'S Manual

Search results

Summary of Contents for 2600

Reviews:

Brands by name

Popular brands