manualshive.com logo in svg

Spectrum SP-UV 200, Operating Manual, Page: 5 / 26

Share
Download
Spectrum SP-UV 200 Operating Manual Download Page 5

 

 
 

1.2 Notes on the User's Manual 

In this manual, the following symbols are used to refer you to warnings and notes: 

 

Warning! 

Warning messages alert you to a specific procedure or practice which, if not followed correctly, could cause 

personal injury. 

 

Caution! 

Caution messages refer you to procedures which, if not observed, could result in damage to the equipment. 

 

Caution! Dangerous electric voltage! 

 

Caution! Emission of UV radiation! 

 

Disconnect power cable! 

 

Note 

This note must be followed to obtain correct measurement results. 

 

For easier navigation within the manual, the manual uses the following system: 



Chapters and illustrations are numbered consecutively. 



Every illustration has its own caption. 



Steps of operation are numbered. 



Cross-references are marked by an arrow (e.g. 

Notes on the User's Manual p.5) 

 

 

 

 

 

 

 

User’s Manual SP-UV 200                                                                              5 
Spectrum Instruments 

Summary of Contents for SP-UV 200



























Reviews:

No comments