Soyal AR-721HV3, Hardware Operation Manual

Page: 3 / 11

8
6. Access Mode
How to program
---2222 Duress Code (network)
---1111 Force On/Off Code (network)
---5678 Door Access User Code (network/standalone)
---1234 Arming and Disarming (network/standalone)
User can select one of the following access modes
AR-721HV3 /1356
Card only
User can access the door by flashing card on the unit.
Arming / Disarming: After flashing card ok, press 1 2 3 4 # Then the
unit will trigger the arming/disarming mode.
Card or PWD
User can access the door by just either flash card or entering 5 digit the user
entering 4 digit user code + #
Arming/Disarming: After flashing card ok, press 1 2 3 4 # . Then the
unit will trigger the arming/disarming mode.
Arming/Disarming: entering 5 digit the user entering 4 digit user code + # ,
then press 1 2 3 4 # . Then the unit will trigger the arming/disarming
mode.
Card or 4-digit User Code
User can access the door by just either flash card or entering 4 - digit user code.
Arming/Disarming: After flashing card ok, press 1 2 3 4 # . Then the
unit will trigger the arming/disarming mode.
Arming/Disarming: entering 4 digit user code, then press 1 2 3 4 # .
Then the unit will trigger the arming/disarming mode.
User can change user code any time
a. AR-721H connects with controller and PC, running 701 client and set user code
variable.
By user: After accessed ok, press 4-digit new user code twice and press
＃
By 701 client \ setting \ user card
b. Not connecting with PC
After accessed ok, press 4-digit new user code twice and press
＃
9
Duress function
This function could help users to send a message to the computer asking for help.
Only available in networking state, running 701 Server and setting 4 sets of Duress
code on PC. (Anyone of these 4 sets is workable.)
This function is not available for CARD ONLY and USER CODE ONLY (AR-721H8)
access.
Access Mode Command Format
Card Only
Not available
Card + user code Flash card, then press Duress code &
＃
User code Only
Not available
User no. + user code
Press user no., then Duress code & ＃
Note: User can access door by duress code instead of user code
under card or user code access mode, but it will be shown ask for
help message in 701 Client \ Daily Transaction Record.
Force on/off Code (4 sets, 4 digits)
Only workable in networking system, running 701 Server and setting 4 sets of
Force code on PC. (Anyone of these 4 sets is workable.)
User could press related code to turn on / off its connected equipment, diagram as
below.
PC boad of Controller AR-716EV2 / AR-727E
COM
JP4
V12
CN5
DI.4
DI.2
DI.1
DI.3
COM
D10
D9
D11
K4
RELAY
K3
D12
RELAY
JP3
K1
K3
K4
K2
K2
RELAY RELAY
K1
Relay Code
K1 16
K2 17
K3 18
K4 19
10
After access OK, press following order to turn on / off its connected equipment.
Access mode ON/Off Order
ON
Flashing card ＋ Force code ＋ Code ＋０＋＃
Card only
Off
Flashing card
＋
Force code
＋
Code
＋１＋＃
ON
Flashing card ＋ User code ＋ Force code ＋ Code ＋
０＋＃
Card + user
code
Off
Flashing card ＋ User code ＋ Force code ＋ Code ＋
１＋＃
ON
User no.
＋
User code
＋
Force code
＋
Code
＋ ０＋
＃
User no. +
user code
(Mode 4)
Off
User no.
＋
User code
＋
Force code
＋
Code
＋ １＋
＃
ON
User code ＋ Force code ＋ Code ＋０＋＃
User code
only
(Mode 8)
Off
User code
＋
Force code
＋
Code
＋１＋＃
This function can be connected with force control television, air conditioning, audio,
etc. by Relay-1, 2, 3, 4 on the multi-door networking controller.
To avoid the conflict of the use of each controller relay, it is user responsibility to
define each controller relay for one purpose use only.
11
7. Function Default Value
Before installing, complete the Parameters setting by calculating
each controller value according to their designated functions.
7.1 For AR-721HV3/ 1356
20
＊
＊ ＊
＊
XXX
＃
＃ ＃
＃
Designated Functions Setting Table
Functions Option Bit Value Remark
Recording every entry/exit
on Time Attendance Report
0:Yes
* 1:No 0 001 network
Auto Re-Lock
0:Disable
* 1:enable 1 002
Auto Open/Auto Disarming 0:Disable
*
1:enable 2 004 network
Door Exit Release
(Push Button)
0:Disable
1:enable
*
4 016
Master Reader /Network
0:minor
* 1:major 5 032 network
Entry / Exit door
0:Exit door
*
1:entry door 6 064
Anti-pass-back door
0:Disable
*
1:enable 7 128
[*] markings is the ex-factory setting, the default value is “ 016 “.
Step 1: Decide each option of function by “0” or “1”.
Step 2: List each value of “1” option
Step 3: Sum up each above value to get the parameter number.
Enable 【 Auto Re-Lock 】 -> 002
Enable 【 Door Exit Release (Push Button) 】 -> 016
+ Enable
【
Anti-pass-back door
】
-> 128
---------------------------------------------------------------------------------------
Total value:
146
Step 4: Command: 2 0 * 1 4 6 #
24*NNN# Particular Functions
Functions Option Bit Value
Star “Auto Open Zone ” function
0: By push button
*
1: Auto. 0 001
Lift Control / Alarm Output 0: Alarm output
* 1: Lift control 1
002
Stop Alarm by…
0: Push button
*
1: Close door 6 064
Doorbell output
0: Disable
*
1: Enable 7 128
[*] markings is the ex-factory setting, the default value is “ 000 “.