40
19.2 For AR-721H6
Be sure to record the user number, the user name, the card ID number (card code), and
the user code and keep this information in a secure place. A black user log form has
been included for purpose. Do not write on this form; use it as a photocopy master.
User no.
User Name
Card code
User code
Function
Command
Programmed Values
Master code
09*PPPPPPCCCCCC#
123456
Door relay release time
02*TTT#
003 (3 seconds)
Common code (1)
15*PPPP#
4321
Common code (2)
17*PPPP#
1234
41
20. F.A.Q.
Q : How to input Duress Code in your SOYAL reader?
Step1. Setting the Duress :
Press * 1 2 3 4 5 6 # button into Editing mode.
When in editing mode, enter 1 5 #
You can enter 4 numbers to be as Duress Code.
Step2. Start the operation :
Press 4 numbers of Duress Code and flashing card.
The Duress will be switched up !
Q : How to configure alarm relay time when the door open too long?
Before this procedure, you have to configure the function “ALARM RELAY TM” ,
“DOOR CLOSE TM” , and “FORCE OPEN”.
Step1. In editing mode, press 0 3 * and enter the time for alarm relay time
setting.
Step2. In edit mode, press 1 8 * and enter the time for alarm triggered setting.
Step3. In edit mode, press 2 8 * and enter 3 numbers.
Close Force-Open order: press 0 0 0
Function Force-Open order :press 1 2 8
Press * * # to quit the edit mode and keep arming.
42
Q : How to set the function “open two door”in your reader ?
First of all, you must make sure that you have the Wiegand Reader used with
AR-721HV3 series in this function.
Press 2 8 * 0 6 4 --Open two doors.
This function is good for using together with auxiliary reader. AR-721 HV3 and auxiliary
reader open different door. Note that this function cannot use with Arming function at the
same time.
Q : How to delete all Transponders in your SOYAL reader ?
In edit mode, press 2 9 * 2 9 * # then the
data will be erased in your system.
Press * # to exit this setting module !!
Q : How to set the door relay release time?
When in edit mode,
Press 0 2 * T T T # Time range is 000~600 sec.
Press the button below, 0 0 0 ~ 6 0 0
It’s mean 000~600 seconds for door relay time.
Press the button below, 0 0 0 Latch/Toggle mode will be functioned.
The door will remain open by flashing card in one time.
The door will remain close by flashing card in one time.
Press the button below, 6 0 1 ~ 6 0 9
It’s mean 0.1~ 0.9 seconds for door relay time.
A green light and beep means the door relay release time was changed.
43
Q : How to function the Arming & Disarming?
Press 1 7 * P P P P # to set 4-digit function code.
Function code followed with # to Arm or Disarm the system.
Default setting : P P P P # is 1234.
Q : How to add Transponder ( Card / Key tag) to the system ?
In edit mode, please press the buttons as below:
1 9 * 1 2 3 4 1 * 1 2 3 4
5 #
Q : How to set Door-bell system ?
Alarm output used with Relay is the formal type of this function.
When you in edit mode , press 2 4 * 1 2 8 #
The Door-bell system will function.
Q : How to set Free access Mode ?
1. Standalone:
In edit mode, please Press 0 + #
2. Networking: connecting with AR-716E
In edit mode, please Press 0 + #
Note:
This function not allowed the reader in standalone when connect to controller.
