Message Playback (Cont.)
Message Capacity Full Detection
If an AC power failure occurs, or the power plug
comes out of the wall, your unit will shut down until
the power is restored.
When the power is restored, any messages recorded
before the power failure will be saved IF YOU
HAVE INSTALLED A 10 VOLT BATTERY. The
message counter will indicate the number of
messages received.
If your unit is not operating properly when the
power is restored, proceed with a unit reset.
To Reset Unit
1.Unplug the AC adapter from the power outlet.
2.Remove the 10 volt battery. Replace with a
fresh 10 volt battery.
3.Plug AC adapter back into power outlet.
4.Record a new personalized outgoing greeting
and reset the voice Time/Day Stamp (see page
36).
Option
Play back new messages
Erase all messages
To record greeting
Return to main memu
If You Press 1
(To Play back Messages)
Erase current message
Repeat current message
Stop message playback
Skip to next message
Fast repeat previous message
2.After being instructed by voice menu, enter your
desired 3-digit security code (except ``*`` ``#``).
The unit will announce the security code that you
have just set. It will save the security after you
input 3-digit.
When the message capacity is full,
the unit will answer the phone and say
``Hello, our machine can`t accept
messages, please call again.`` pause 10
seconds, and then automatically
disconnect the telephone line.
If the unit answers before you do, you can turn it
off by picking up any extension phone or pressing
the TALK button on your handset. If the unit does
not stop answering, press the hook switch or
FLASH button for about one second and release.
You may also press the STOP button on the base.
The message counter will flash and display ``FU``.
You should erase some messages to make room in
memory.
To listen to an incoming call without picking up
the phone, let your unit answer the phone when it
rings. If you don`t want to talk to the caller, let
your unit take a message, and adjust
the volume control on the side of the unit to listen.
If you don`t want to listen to the caller`s message,
lower the volume.
Call Screening
Call Interrupt
To SAVE messages, Hang up the
Telephone.
If You Press 3
(Record Answer On Greeting when set to
Answer on mode already.
Record Announce Only Greeting when set to
Announce Only Mode already.
To Record New Outgoing Greeting)
1.The unit will say ``Record greeting after the beep.
Press 5 to end recording.``
2.Record your new outgoing greeting (up to 60
seconds).
3. When you have finished recording your outgoing
greeting, press 5. The new outgoing greeting will
play back to you.
Power Failure
Protection/ Battery Backup
Note:
Callers will be unaware that you are screening
their calls. If you want to talk to the caller,
pick up an extension phone or press the
TALK button on your handset .
Tone Remote Operation
To access answer functions from an outside line,
you will need to enter the three digits security code.
To set the security code:
1.Press CH/CS/REMOTE button, then press the
``8`` on the GH3080 keypad to access the security
code set operation.
33
34
Pr ess
(1)
(2)
(3)
(7)
Pr ess
(2)
(4)
(5)
(6)
(4)(4)
During a power outage, your unit will NOT work
even if a 10 volt battery is installed.
The battery will save your outgoing greeting, and
any incoming message you have already received.
IMPORTANT
FU
To Check Security Code:
1.Press CH/CS/REMOTE button, then press ``8``
on the GH3080 keypad to access the security code
operation.
2.The unit will announce the currently set security
code.
To Turn On Answering Machine Remotely:
If you forget to turn on your unit, call your phone
number from an outside touch tone telephone.
Wait 10 rings until the machine answers, hang up
the telephone, and subsequent calls will be answered.
To access Answering Machine Remotely:
1.Call your phone number from a touch tone
telephone.
2. After the unit answers, enter your two digit
security code during playback of the outgoing
greeting.
3.If the code was entered corretly, the unit will stop
playing back the outgoing greeting and will sound
two beeps.
4. The voice menu will direct you to press the
following buttons on your keypad:
Write this number on the REMOTE ACCESS
CARD, which you can keep in your wallet. If you
do not set a security code, the default security code
is ``308``.
PDF created with FinePrint pdfFactory trial version
http://www.fineprint.com