background image

  southpaw enterprises, inc.

® 

Instruction Sheet

 

In-FUN-ity                        

Rope  152016 

Store these instructions in a safe place or 
with the enclosed maintenance checklist 

Take time to familiarize yourself with the use and maintenance of this equipment before using.  Please file 
this Instruction Sheet in an accessible location:  the Instruction Sheet must be read and familiar to anyone 
who is using Southpaw Enterprises Equipment.   

IMPORTANT: Please check equipment immediately for any damage that may have resulted during shipping.   
If any damage has occurred, please contact Southpaw Enterprises, Inc. immediately. 

MATERIALS LIST:

 

1 - 3/4” X 12 ft. rope 
1 - Instruction Sheet 
1 - Maintenance Checklist 
 

ATTACHMENT INSTRUCTIONS:

 

• 

Put the loop end of the rope behind the ladder rung at the appropriate 
height.  Put the tag end of the rope through the loop as shown in fig. 1. 

• 

Pull on the tag end of the rope until the formed loop is tight around the 
ladder rung as shown in fig. 2. 

 

STORAGE PROCEDURE:

 

• 

Store where not accessible without supervision. 

 

CLEANING INSTRUCTIONS:

 

Check with your infectious disease department before using these proce-
dures. 

• 

Check for client allergies first. 

• 

Wipe rope with a damp cloth using mild soap and water or disinfectant. 

• 

Dry before using. 

• 

DO NOT machine wash. 

 

MAINTENANCE CHECKLIST:

 

• 

Check that rope is secure on the ladder rung. 

• 

Check for cuts.  If cuts are found, discontinue use. 

• 

Small whiskers developing on the rope are normal with use and not considered a hazard.  

Fig. 1 

Fig. 2 

Safety Precautions - 

The safety of your clients is dependent on the appropriate choice of activity to match, yet challenge their 

physical abilities.  Use appropriate spotting / safety techniques.  In addition, the layout of your activity area, proper installation and 
maintenance  of your equipment is critical.  Southpaw equipment is not intended for recreational or outdoor use.  Under no condition 
should this equipment be used without proper supervision. 
 

This sheet is for example only.  

It is not meant to, in any way, replace local, county, state, or Federal standards.  Be aware - it is 

your responsibility to find all pertinent safety information that pertains to your facility.  

Southpaw 
Enterprises Inc.

®

 

If you have any questions or comments, please call or write 

Southpaw Enterprises, Inc. 

P.O. Box 1047, Dayton, Ohio 45401 -1047 

Toll Free - (800) 228-1698 

Come see us on the World Wide Web at http://southpawenterprises.com 

FORM 

CODE: 

XI-152016 

   © 

2004 

Southpaw 

Enterprises, 

Inc. 

TM 

Summary of Contents for In-FUN-ity Climbing System
























Reviews: