background image

Safety Precautions - 

The safety of your clients is dependent on the appropriate choice of activity to match, yet challenge their 

physical abilities.  Use appropriate spotting / safety techniques.  In addition, the layout of your activity area, proper installation and 
maintenance  of your equipment is critical.  Southpaw equipment is not intended for recreational or outdoor use.  Under no condition 
should this equipment be used without proper supervision. 
 

This sheet is for example only.  

It is not meant to, in any way, replace local, county, state, or Federal standards.  Be aware - it is 

your responsibility to find all pertinent safety information that pertains to your facility.  

Southpaw 
Enterprises Inc.

®

 

If you have any questions or comments, please call or write 

Southpaw Enterprises, Inc. 

P.O. Box 1047, Dayton, Ohio 45401 -1047 

Toll Free - (800) 228-1698 

Come see us on the World Wide Web at http://southpawenterprises.com 

 

FORM CODE: XI-152015 

 

 

 

© 2004 Southpaw Enterprises, Inc. 

CLEANING INSTRUCTIONS:

 

• 

Check with your infectious disease department before using these procedures.  

• 

Check for client allergies first. 

• 

Clean with a damp cloth using soap and water or disinfectant. 

• 

Dry before using. 

 

Summary of Contents for In-FUN-ity Climbing System
























Reviews: