Sony PCM-7040, Operation Manual

Page: 75 / 91

Chapter 8
8-2
Chapter 8 Application Systems
Notes
• “VIDEO” appears on the display when the video
sync signal is input to this unit, and the setting of
“rEF tcF” in the setup menu matches the sync signal
frequency. If the “VIDEO” indication on the display
is blinking, check the setting of the video sync signal
and the time code format.
• Set the time code format correctly by using “rEF tcF”
in the setup menu. This unit does not automatically
distinguish between the drop frame time code and the
non-drop frame time code.
• Confirm the “SYNC PB” indication appears on the
display when this unit is playing back.
BVE-9100/9000/2000/910/900/600 Video Editor
settings
1
Set the TC SOURCE in the AUX mode to “LTC”,
“LTC+”, “LTC:VITC” or “LTC:VITC+”.
2
When using the following video editor
BVE-900 (without BKE-900K): V1.11 or higher
BVE-900 (with BKE-900K): V2.03 or higher
BVE-910: V2.10 or higher
BVE-2000
BKE-9611/9004/9004A/9012 of the BVE-9000/
9100: V2.01 or higher
Set the device types BYTE 1 and 2 of block-1
(CONSTANT-1) to “FF” (UNDEFINED). In this
case, VTR CONFIGURATION is automatically
set depending on the device type.
When using BVE-600/900/910/9000/9100 editors
other than the models listed above.
Set the following VTR constants.
NTSC: When the setup menu “rEF-tcF” is set to
“30ndF”, “29 97 ndF” or “29 97 dF”
PAL: When the setup menu “rEF-tcF” is set to “25
Ebu”
Machine parameter group
Device type
00 96 05 05 03 80
3 4 5 6 7 8
00 96 05 05 03 80
1 2 3 4 5 6 7 8
PCM-
7040
NTSC
PCM-
7040
PAL
VTR
Block-1 (CONSTANT-1) Block-2 (CONSTANT-2)
70 00 0A 09 FF F6 00 5C FF 5A
71 00 0A 09 FF F6 00 4C FF 4B
Set the following machine parameters when the
software version of the BKE-9611/9004/9004A/9012
of the BVE-9000/9100 is 2.00 or lower.
Notes
• You can use the first edit function of the video editor,
when you set the setup menu “1St Edit” item to “on”
and use a blank tape.
• When this unit enters FF or REW mode, the time
code indication on the Video Editor may blink.
Memory jog from video editor
To perform memory jog under control of the video
editor, follow the procedure blow.
When using the following BVE-910/2000/9100 video
editor to control memory jog
Software version with which memory jog can be
performed:
BVE-910: V2.10 or higher
BVE-9100:
BKE-9101/9102: V1.04 or higher
BKE-9611/9004/9004A/9102: V2.01 or higher
Settings of this unit
1
Set the setup menu “JoG ctL” item to “oFF”.
2
Set the setup menu “StArt” item to “Edit-E” or
“Edit-c”.
1 2 3 4 5 6 7 8
Block-4 (VTR CONFIGURATION)
Machine parameter group
PCM-7040
NTSC, PAL
01 00 88 71 03 7C 00 00
VTR
8-2 Systems with Editing Capability and Their Applications