2
MZ-B10
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 ˚C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C .
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur
such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
On power sources
•
Use house current, LR6 (size AA) battery.
•
For use in your house: use the AC power adaptor
supplied with this recorder. Do not use any other
AC power adaptor since it may cause the recorder
to malfunction.
•
Connect the AC power adaptor to an easily
accessible AC outlet. Should you notice an
abnormality in the AC power adaptor,
disconnect it from the AC outlet immediately.
•
The recorder is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the
recorder itself has been turned off.
•
If you are not going to use this recorder for a
long time, be sure to disconnect the power
supply (AC power adaptor, dry battery).
To
remove the AC power adaptor from the wall
outlet, grasp the adaptor plug itself; never pull
the cord.
Polarity of the
plug
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED
LINE WITH MARK
0
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
Battery life
The battery life may be shorter due to operating
conditions and the temperature of the location.
When recording
1)2)
(Unit: approx.hours)(JEITA
3)
)
1)
When using a Sony LR6 (SG) “STAMINA”
alkaline dry batteries (produced in Japan) and
“PowerMode” is set to “NORMAL”
(page 40). Setting “PowerMode” to “QUICK”
result in a shorter battery life (page 40).
2)
When recorded with the built-in microphone.
Recording mode
Approx. hours
SP
24
LP2
34
LP4
48
MONO
34
Notes
Stop the recorder before replacing batteries.
An optional AC power adaptor is
recommended for long recording.
3)
Measured in accordance with the JEITA
(Japan Electronics and Information
Technology Industries Association) standard.
When playing
1)
(Unit: approx.hours)(JEITA
2)
)
Recording
mode
Speaker
3)
Headphones/
earphones
4)
SP
45
90
LP2
50
100
LP4
55
110
MONO
50
100
1)
When using a Sony LR6 (SG) “STAMINA”
alkaline dry batteries (produced in Japan) and
“PowerMode” is set to “NORMAL” (page 40).
2)
Measured in accordance with the JEITA
(Japan Electronics and Information
Technology Industries Association) standard.
3)
When played using the built-in speaker.
4)
When played using headphones/earphones.
Summary of Contents for MZ-B10 - Minidisc Voice Recorder
Page 63: ...MZ B10 63 MEMO ...
