Sony Handycam DCR-TRV11, Service Manual, Page: 160 / 215

5-45
3-1-2. Precautions on Adjusting
1) The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to “VCR” (or
“PLAYER”) or set the “Forced VTR Power ON mode” using
the adjustment remote commander (Note 1).
To set to the Camera mode, set the power switch to “CAMERA”
or set the “Forced Camera Power ON mode” using the
adjustment remote commander (Note 2).
After completing adjustments, be sure to exit the “Forced VTR
Power ON Mode” or “Forced Camera Power ON Mode”.
(Note 3)
2) The front panel block (MA-385 board, microphone unit, remote
commander receiver, LANC/DIGITAL I/O jack, MIC jack)
must be assembled because the audio/video jack is used for
connecting the monitor TV. To remove, disconnect the following
connector.
MA-385 board CN2071 (28P, 0.5mm)
3) Cabinet (R) (CK-92/94board, LCD block) need not be
connected. But removing the cabinet (R) (removing the VC-
240/241 board CN003) means removing the lithium 3V power
supply (CK-92/94 board, BT3201) , data such as date, time,
user-set menus will be lost. After completing adjustments, reset
these data. If the cabinet (R) has been removed, the self-
diagnosis data, data on history of use (total drum rotation time
etc.) will be lost. Before removing, note down the self-diagnosis
data and the data on the history use (data of page: 2, address:
A2 to AA). (Refer to “SELF-DIAGNOSIS FUNCTION” for
the self-diagnosis data, and to “5-4.Service Mode” for the data
on the history use.)
To remove the cabinet (R), disconnect the following connectors.
VC-240/241 board CN003 (51P, 0.3mm)
4) The viewfinder (LB-64 board) is need not be connected. To
remove it, disconnect the following connector.
DD-137 board CN1604 (27P, 0.3mm)
5) For extension between the DD-137 board CN1603 and VC-
240/241 board CN002, use the following extension cable.
J-6082-395-A (80P, 0.4mm)
6) Only for the DCR-TRV20/TRV20E model, the lens block
(CN701 of VC-240 board) must be connected when performing
adjustments, because the timing generator (IC102) is provided
on the CD-252 board of the lens block.
Note 1: Setting the “Forced VTR Power ON” mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the VTR power to be turned
on with the control switch block (FK-30150 block) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.
Note 2:
Setting the “Forced Camera Power ON” mode (Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (FK-30150 block) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.
Note 3: Setting the “Forced Memory Power ON” mode (Memory mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 05, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the memory power to be
turned on with the control switch block (FK-30150 block)
removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.
Note 4: Exiting the “Forced Power ON” mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
Note 5:
CK-92 board: DCR-TRV11/TRV11E/TRV20
CK-94 board: DCR-TRV6/TRV6E/TRV20E
VC-240 board: DCR-TRV20/TRV20E
VC-241 board: DCR-TRV6/TRV6E/TRV11/TRV11E