Sony Handycam DCR-TRV11, Service Manual

Page: 125 / 215

5-10
1-2. INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE
DATA
1-2-1. INITIALIZATION OF C, D, 8 PAGE DATA
1. Initializing the C, D, 8 Page Data
Note1: If “Initializing the C, D, 8 Page Data” is performed, all data of the
C page, D page and 8 page will be initialized. (It is impossible to
initialize a single page.)
Note2: If the C, D, 8 page data has been initialized, the following
adjustments need to be performed again.
1) Modification of C, D, 8 page data
2) Serial No. input
3) Servo and RF system adjustments
4) Video system adjustments
5) Color viewfinder system adjustments
6) LCD system Adjustments
Adjusting page C
Adjusting Address 10 to FF
Adjusting page D
Adjusting Address 10 to FF
Adjusting page 8
Adjusting Address 00 to FF
Initializing Method:
1)
Select page: 0, address: 01, and set data: 01.
2) Select page: 3, address: 81, and check that the data is “00”.
3) Select page: 3, address: 80, set data: 0A, and press the PAUSE
button of the adjustment remote commander.
4) Select page: 3, address: 80, and check that the data changes to
“1A”.
5) Perform “Modification of C, D, 8 Page Data”.
2. Modification of C, D, 8 Page Data
If the C, D, 8 page data has been initialized, change the data of the
“Fixed data-2” address shown in the following tables by manual
input.
Modifying Method:
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of C, D, 8 Page data
1)
Select page: 2, address: 00, and set data: 29.
2) Select page: 2, address: 01, and set data: 29, and press the
PAUSE button of the adjustment remote commander.
Note: If the following symptoms occur after completing of the
“Modification of C, D, 8 page data”, check that the data of the
“Fixed data-2” addresses of D page are same as those of the
same model of the same destination.
1) The battery end mark on the LCD or viewfinder screen is
flashing.
2) The power is shut off so that unit cannot operate.
3. C Page Table
Note:
Fixed data-1: Initialized data. (Refer to “1. Initializing the C, D, 8
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8
Page Data”.)
00 to 0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D to 3F
40
41
42
43 to 4B
4C
4D
4E
4F
50
51
52 to 63
64
65 to 83
84
85
EE
00
00
00
E0
2A
2A
32
32
25
3E
3E
DC
99
88
E3
A1
04
20
03
Switching position adj.
Fixed data-1
(Initialized data)
Cap FG duty adj.
Fixed data-2
AEQ adj.
Fixed data-1
AEQ adj.
Fixed data-1
AGC center level adj.
PLL f
0
adj.
APC adj.
LPF f
0
adj.
Fixed data-1
(Initialized data)
S VIDEO out Y level adj.
S VIDEO out Cr level adj.
S VIDEO out Cb level adj.
Chroma BPF f
0
adj.
PLL f
0
fine adj.
Fixed data-1
(Initialized data)
APC adj.
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
(Initialized data)
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1
(Initialized data)
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1
(Initialized data)
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Address Remark
Initial value