Sony Handycam DCR-PC5 Operating Instructions Manual Download Page 7

Page: 7 / 156

Quick Start Guide

Recording a picture

(p. 18)

Remove the lens cap.

Set the POWER switch to CAMERA
while pressing the small green
button. The power lamp lights up.

POWER

LOCK

VCR

MEMORY

CAMERA

OFF

POWER

LOCK

VCR

MEMORY

CAMERA

OFF

Press START/STOP. Your camcorder

starts recording. To stop recording,
press START/STOP again.

When the

LCD panel
is closed,
pull out the
viewfinder
until it
clicks. Use
the
viewfinder
placing
your eye
against its
eyecup.

Monitoring the playback picture on the LCD

screen

(p. 27)

NOTE

Do not pick up your
camcorder by holding the
viewfinder, the LCD panel,
the battery pack or the jack
cover.

Set the POWER switch to VCR while
pressing the small green button.

Press

of the touch panel to

rewind the tape.

Press

of the touch panel to

start playback.

NOTE

When using the touch panel, press
operation buttons lightly with your
thumb supporting the LCD screen from
the backside of it. Do not press the LCD
screen with sharp-pointed objects such
as pens.

Press OPEN
to open the
LCD panel.

POWER

LOCK

VCR

MEMORY

CAMERA

OFF

Summary of Contents for Handycam DCR-PC5





























































































































































Search results

Summary of Contents for Handycam DCR-PC5

Reviews:

Sony Handycam DCR-PC5, Operating Instructions Manual, Page: 7 / 156

Search results

Summary of Contents for Handycam DCR-PC5

Reviews: