Sony Handycam DCR-PC5 Operating Instructions Manual Download Page 42

Page: 42 / 156

Using special effects – Digital effect

(

)

In CAMERA mode, press FN to display PAGE1 (p. 16).

(

)

Press DIG EFFT. The screen to select a desired digital effect mode appears.

(

)

Select a desired digital effect mode. In the STILL and LUMI. modes, the still
picture is stored in memory.

(

)

Press –/+ to adjust the effect.

Items to adjust

STILL

The rate of the still picture you want to superimpose on the moving
picture

FLASH

The interval of flash motion

LUMI.

The color scheme of the area in the still picture which is to be swapped
with a moving picture

TRAIL

The vanishing time of the incidental image

SLOW SHTR

Shutter speed. The larger the shutter speed number, the slower the
shutter speed.

OLD MOVIE

No adjustment necessary

(

)

Press

OK to return to PAGE1.

To return to FN

Press EXIT.

To cancel the digital effect

Press

OFF to return to PAGE1.

LUMI.

–

OFF

2~4

DIG
EFFT

DIG EFFT

STILL

SLOW

SHTR

OLD

MOVIE

OFF

LUMI.

FLASH

TRAIL

The bar appears when setting following
digital effect modes : STILL, FLASH,
LUMI., TRAIL.

Summary of Contents for Handycam DCR-PC5





























































































































































Search results

Summary of Contents for Handycam DCR-PC5

Reviews:

Sony Handycam DCR-PC5, Operating Instructions Manual, Page: 42 / 156

Search results

Summary of Contents for Handycam DCR-PC5

Reviews: