Sony Handycam DCR-PC10, Service Manual

Page: 8 / 181

— 8 —
4. Self-diagnosis Code Table
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E
E
E
Block
Function
2 1
2 2
2 3
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 2
3 2
3 2
3 2
3 2
3 2
3 2
3 2
3 2
3 2
6 1
6 1
6 2
6 2
Detailed
Code
0 0
0 0
0 0
1 0
1 1
2 0
2 1
2 2
2 3
2 4
3 0
4 0
4 2
1 0
1 1
2 0
2 1
2 2
2 3
2 4
3 0
4 0
4 2
0 0
1 0
0 0
0 1
Symptom/State
Condensation.
Video head is dirty.
Non-standard battery is used.
LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
T reel side tape slacking when unloading.
S reel side tape slacking when unloading.
T reel fault
S reel fault
T reel fault
FG fault when starting capstan
FG fault when starting drum
FG fault during normal drum operations
LOAD direction loading motor time-
out
UNLOAD direction loading motor
time-out
T reel side tape slacking when
unloading.
S reel side tape slacking when
unloading.
T reel fault
S reel fault
T reel fault
FG fault during normal capstan
operations
FG fault when starting drum
FG fault during normal drum
operations
Difficult to adjust focus
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
Steadyshot function does not work
well. (With pitch angular velocity
sensor output stopped.)
Steadyshot function does not work
well. (With yaw angular velocity sensor
output stopped.)
Self-diagnosis Code
Repaired b
y
:
Correction
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Use the info LITHIUM battery.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Inspect the lens block focus reset sensor (Pin
@¡
of CN100 of
CD-175 board) when focusing is performed when the focus
button of the remote control (e.g. RM-95) is pressed in the focus
fixing mode, and the focus motor drive circuit (IC204, IC404 of
VC-199 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin
!¡
of CN100 of
CD-175 board) when zooming is performed when the zoom lens
is operated and the zoom motor drive circuit (IC204, 404 of VC-
199 board) when zooming is not performed.
Inspect pitch angular velocity sensor (SE501 of FP-615 flexible
board) peripheral circuits.
Inspect yaw angular velocity sensor (SE500 of CD-175 board)
peripheral circuits.