Sony Digital betacam DVW-707, Maintenance Manual, Page: 31 / 314

2-7
DVW-790WS/709WS/707
DVW-790WSP/709WSP/707P P2V1
No. Page Item Setup Description
15 VF SETTING ZEBRA 1 DETECT 20 to 107 % (
[70]
) Sets the center level of the zebra 1 pattern.
ZEBRA 1 APERTURE 1 to 20 % (
[10]
) Sets the width of the zebra 1 pattern.
ZEBRA 2 DETECT 52 to 109 % (
[100]
) Sets the ZEBRA2 display level.
ZEBRA SELECT
[1]
/2/BOTH Selects the zebra patterns.
TEST OUT ZEBRA ON/
[OFF]
Turns ON/OFF the function of outputting the zebra pattern to TEST OUT.
VF DTL LEVEL X (
[0]
) Sets the VF detail amount.
16 LEVEL 1 DETAIL LVL X (
[0]
) Sets the total level of the detail signal.
H/V RATIO X (
[0]
) Sets balance between the H detail signal and the V detail signal.
DTL FREQ X (
[0]
) Sets frequency (thickness) of the H detail signal.
CRISPENING X (
[0]
) Sets the crispening level of the detail signal.
APT. LEVEL X (
[0]
) Sets the high-frequency correction level.
DTL W.CLP X (
[0]
) Sets the white clip level of the V detail signal.
DTL V B.CLP X (
[0]
) Sets the level that clips the excessive level in the negative ( _ )
direction of the V detail signal.
DTL H B.CLP X (
[0]
) Sets the level that clips the excessive level in the negative ( _ )
direction of the H detail signal.
LVL DEPEND
[ON]
/OFF Turns ON/OFF the level dependent function
L.DEP.LVL X (
[0]
) Sets the level that suppresses the detail signal at the low signal level.
17 LEVEL 2 KNEE APT ON/
[OFF]
Turns ON/OFF the knee aperture function.
K.APT.LVL X (
[0]
) Adjusts the detail signal amount that is added to the high light
signal higher than the knee point.
DTL COMB X (
[0]
) Set the signal level at which the comb filter starts working.
C.C.S.LVL X (
[0]
) Sets the chroma suppression level. (NTSC only)
18 LEVEL 1#4:3 Note : This page is displayed only in DVW-790WS/790WSP/
709WS/709WSP.
The following settings are valid when the 16:9/4:3 MODE
on the WIDE SCREEN is set to 4:3.
DETAIL LVL X (
[0]
) Sets the overall level of the detail signal.
H/V RATIO X (
[0]
) Sets balance between the H detail signal and the V detail signal.
DTL FREQ X (
[0]
) Sets frequency (thickness) of the H detail signal.
CRISPENING X (
[0]
) Sets the crispening level of the detail signal.
APT. LEVEL X (
[0]
) Sets the high frequency correction level.
DTL W.CLP X (
[0]
) Sets the white clip level of the V detail signal.
DTL V B.CLP X (
[0]
) Sets the level that clips the excessive level in the negative (
_
)
direction of the V detail signal.
DTL H B.CLP X (
[0]
) Sets the level that clips the excessive level in the negative (
_
)
direction of the H detail signal.
LVL DEPEND
[ON]
/OFF Turns ON/OFF the level dependent function
L.DEP.LVL X (
[0]
) Sets the level that suppresses the detail signal at the low signal level.
19 LEVEL 2#4:3 Note : This page is displayed only in DVW-790WS/790WSP/
709WS/709WSP.
The following settings are valid when the 16:9/4:3 MODE
on the WIDE SECREEN is set to 4:3.
KNEE APT ON/
[OFF]
Turns ON/OFF the knee aperture function.
K.APT.LVL X (
[0]
) Adjusts the detail signal amount that is added to the high light
signal higher than the knee point.
DTL COMB X (
[0]
) Set the signal level at which the comb filter starts working.
C.C.S.LVL X (
[0]
) Sets the chroma suppression level. (NTSC only)
2-1. Service Mode