![background image](http://html.mh-extra.com/html/sony/cdm74hf-dvbu101/cdm74hf-dvbu101_service-manual_420235035.webp)
HCD-GZR5D
HCD-GZR5D
35
35
For Schematic Diagrams.
Note:
• All capacitors are in
μ
F unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in
Ω
and 1/4 W or less unless otherwise
speci
fi
ed.
•
2
: non
fl
ammable resistor.
•
C
: panel designation.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
•
A
: B+ Line.
•
B
: B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
*
: Impossible to measure
• Voltages are taken with VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
:
AUDIO
f
:
TUNER
L
:
VIDEO
E
:
TAPE
PLAY
a
:
TAPE
REC
J
: DVD (AUDIO)
c
: DVD (RF)
I
: DVD (DIGITAL)
N
:
MIC
: PHONES
• Abbreviation
E3
: 240V AC area in E model
E12
: 220 – 240V AC area in E model
E15
: Iran model
PH
: Philippines model
SP
: Singapore model
TH :
Thai
model
For Printed Wiring Boards.
Note:
•
X
: Parts extracted from the component side.
•
Y
: parts extracted from the conductor side.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Abbreviation
E3
: 240V AC area in E model
E12
: 220 – 240V AC area in E model
E15 :
Iran
model
PH :
Philippines
model
SP :
Singapore
model
TH :
Thai
model
Note:
The components identi
fi
ed by mark
0
or dotted
line with mark
0
are critical for safety.
Replace only with part number speci
fi
ed.
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(
Caution:
Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution:
The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to
fl
ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
• Waveforms
– DMB18 Board –
– MAIN Board –
Summary of Contents for CDM74HF-DVBU101
Page 30: ...HCD GZR5D 30 MEMO ...
Page 101: ...MEMO HCD GZR5D 101 ...