background image

Quick Start Guide for HARMONi G3

5

3.

Remove the heatsink and set it down with the fins face down 

(Figure 11)

.

4.

While holding down the logic board/drive assembly with one hand, insert
the hook end of the processor card removal tool under the bottom left cor-
ner of the processor card, then 

gently

and slowly pull straight up on the edge

of the card to disengage it from the logic board 

(Figure 12)

Do not attempt to

pry out the processor card; you may damage it

.

Move RAM From Processor Card to HARMONi Processor Card

Depending on the configuration of your iMac, your processor card may have
RAM (memory) modules installed on both sides of the processor card. 

1.

Turn the processor card over so the two long connectors are face up 

(Figure 13)

. Grasping the processor card by its edges, gently pull apart the

retainer clips on both sides of the RAM module 

(Figure 13)

; the module will

pop up. Remove the module, then set it and the processor card aside on a
static-free surface.

2.

Remove the HARMONi processor card from its anti-static bag, making sure
to handle the card by its edges 

(Figure 14)

. If present on the card, remove

the foam block protecting the small 4-pin connectors.

3.

Turn the HARMONi processor card over, so that the two long connectors are
face up 

(Figure 15)

. Align the RAM module removed from the bottom of the

original processor card with the RAM slot on the HARMONi processor card,
and insert it at a 30˚ angle, all the way into the slot 

(Figure 15)

Figure 15

Figure 14

anti-static bag

HARMONi processor card

HARMONi processor card

Figure 12

Figure 13

Figure 11

Support Note:

Do not touch the RAM modules’ connectors; always

handle RAM only by its edges. 

Support Note:

If you are installing two RAM modules into the

HARMONi card, be sure to install them into the expansion slots that 

correspond to those on the original processor card. When you install RAM, note
that the modules are designed to fit into the slot only one way; align the notch
in the module to the guide in the slot.

RAM module

RAM slot

30˚

heat sink

processor card

tool

RAM module

clip

clip

foam block

Summary of Contents for HARMONi G3












Reviews: