background image

Quick Start Guide for HARMONi G3

iMac and Operating System Compatibility

The HARMONi G3 iMac processor/FireWire upgrade is compatible 

only

with

iMac

®

233, 266, and 333 MHz models (Revisions A-D); do not install this product

into models with faster (350 MHz or higher) processors. If you are unsure which
iMac model you have, look at the front of your computer; compatible
models have tray-loading CD-ROM players.

At this printing, the HARMONi G3 iMac processor/FireWire upgrade is
compatible with Mac

®

OS 8.1 through the latest version of OS X. FireWire

requires OS 8.6 or later; best compatibility with FireWire devices is achieved
with OS 9.1 or later, and OS X Version 10.1 or later. For up-to-date Mac OS
compatibility information, check our website at www.sonnettech.com.

You Should Have

The following items should be included in your product package:

• HARMONi G3 processor upgrade card

• FireWire adapter card

• Adapter card power cable

• Standoff for adapter card

• Replacement side plate

• Three small screws

• Plastic wire clamp

• Processor card removal tool

• Sonnet Installer CD

The following items are required for installation:

• #1 and #2 Phillips screwdrivers

• Flat blade screwdriver

• Soft, clean towel

System Requirements

The HARMONi requires the following in order to work in your system: 

• Fully operational original processor (you must install Sonnet software prior to 

installing the HARMONi parts)

• FireWire 2.3.3 or later (

this driver should be installed after HARMONi has been

installed; instructions follow

)

Software updates and links are available from the Sonnet web site at www.sonnettech.com.

Remember to register your product online at http://registration.sonnettech.com to be informed of future upgrades and product releases.

Sonnet Technologies Customer Service hours are Monday-Friday, 8am-5pm Pacific Time • Customer Service Phone: 1-949-472-2772 • E-mail: [email protected]

Sonnet Technologies, Inc., 15 Whatney, Irvine, California 92618-2808 USA • Tel: 1-949-587-3500 Fax: 1-949-457-6350

©2002 Sonnet Technologies, Inc. All rights reserved. Sonnet, the Sonnet logotype, Simply Fast, the Simply Fast logotype, and HARMONi are trademarks of Sonnet Technologies, Inc. Macintosh and Mac are trademarks of Apple
Computer, Inc., registered in the United States and other countries. Other product names are trademarks of their respective owners. Product specifications subject to change without notice. Printed in the USA.
HAFWG3-QS-E-040302

HARMON

i

™ 

G

3

  

iMac

®

 Processor/FireWire

® 

 Upgrade

Summary of Contents for HARMONi G3












Reviews: