Sonifex Phone In 6 User Handbook Manual Download Page 31

Page: 31 / 34

Phone In 6 User Handbook

TECHNICAL SPECIFICATION

TECHNIC

AL SPECIFIC

TION

Technical Specification

Audio Inputs

Input Impedance – Line Mode >10kΩ balanced 0dB, optimum working input
(Mix-minus audio to caller):
Input Level Range:

Adjustable 0 to +12dBu

ADC Signal to Noise:

Better than –89dbFS (RMS A-weighted at 24bit)

ADC Dynamic Range:

>96dB

ADC Distortion & Noise:

>87dB THD + N at 1kHz

ADC Frequency Response:

20Hz to 3.8kHz

Optional Digital Audio:

AES/EBU 110 Ω balanced inputs (IEC60968)

Sample Rates:

32kHz to 96kHz

0dBFS Reference Level:

12dBu or 18dBu

Audio Outputs

Output Impedance

<50Ω balanced floating 0dB, optimum working input

(Received audio from caller):
Output Level Range:

Adjustable -6 to +6dBu

DAC Signal to Noise:

Better than –85dbFS (RMS A-weighted at 24bit)

DAC Dynamic Range:

>97dB

DAC Distortion & Noise:

>83dB THD + N at 1kHz

DAC Frequency Response:

20Hz to 3.8kHz

Optional Digital Audio:

AES/EBU 110 Ω balanced outputs (IEC60968)

Sample Rates:

32kHz to 96kHz

0dBFS Reference Level:

12dBu or 18dBu

PSTN Telephone Connection

Send to Line Limiting Input:

+4dBu

Bandwidth to Telephone Line: 125Hz – 3.8kHz, -3dB ref 1kHz
Telephone Line Impedance:

Nominally 600Ω - complex impedances set via country

code

Telephone Line

300Ω to 1500Ω

Impedance Range:
Telephone Rejection:

78dB on 1kHz tone, typically 75dB on complex

waveforms, reference peak level of 0dB

Ring Detector Sensitivity:

1 ring to 8 rings

ISDN Telephone Connection

ISDN Interface:

S0 (BRI) / I.430

D Channel Protocol:

DSS1, National 1, 5ESS, JATE (INS64), AUSTEL, X.31, VN 4,

TPH 1962

B Channel Protocol:

G.711

Regulatory Approval:

Summary of Contents for Phone In 6



































Search results

Summary of Contents for Phone In 6

Reviews:

Related manuals for Phone In 6

Brands by name

Popular brands

Sonifex Phone In 6, User Handbook Manual

Search results

Summary of Contents for Phone In 6

Reviews:

Related manuals for Phone In 6

Brands by name

Popular brands