manualshive.com logo in svg

Sonifex Phone In 6, User Handbook Manual

Share
Download
Sonifex Phone In 6 User Handbook Manual Download Page 26

14

Phone In 6 User Handbook

4

REMO

TE C

ONTR

OL P

ANEL

REMOTE CONTROL PANEL

LOCAL Button 

This is used to connect and disconnect a caller to the headset or to 
make a call on a free line, i.e. to use the headset to speak to caller’s, 
have the LOCAL button selected. The button has a latching operation.

The following three buttons are replicated for up to 6 telephone lines, numbered 1 - 6 
along the top of the buttons:

LINE HOLD/Release Button

The LINE HOLD/Release button is used to control the line hold circuit, 
it illuminates to indicate the status of the line and flashes to show ring 
status.

ON AIR Button Hybrid 1

The ON AIR 1 button is used to route the caller to air on hybrid 1. The 
indicator in the button illuminates to show that the caller is on air . In 
Conference Mode, two callers can be put to air on Hybrid 1.

ON AIR Button Hybrid 2

The ON AIR 2 button is used to route the caller to air on hybrid 2. The 
indicator in the button illuminates to show that the caller is on air. In 
Conference Mode the On Air 2 button has no function.

Fig 4-4: LOCAL Button

Fig 4-5: LINE HOLD/Release Button

Fig 4-6: ON AIR 1 Button

Fig 4-7: ON AIR 2 Button

Summary of Contents for Phone In 6



































Reviews:

No comments

Brands by name

Popular brands

Load more brands