14
Copyright © 2011 Somfy SAS. All rights reserved.
FR
Elixo 800/1300/2000
9. paRamétRaGe
Fonctionnement
Réglage
Description du fonctionnement
mode de
fonctionnement
cellules
photoélectriques
12
ON
SW
2
entrée cellules photoélectriques active seulement en fermeture
: si les cellules
sont occultées en fermeture, le portail s’arrête puis repart en ouverture. Si elles sont
occultées en ouverture, le portail continue à s’ouvrir.
1
2
ON
SW2
entrée cellules photoélectriques active en ouverture et en fermeture
: si les
cellules sont occultées en ouverture, le portail s’arrête et repart quand elles ne sont
plus occultées. Si elles sont occultées à la fermeture, le portail s’arrête puis repart en
ouverture.
active/désactive
fonction fermeture
automatique avec
passage devant les
cellules
1
2
ON
SW
2
Fonction fermeture automatique désactivée.
1
2
ON
SW
2
Fonction fermeture automatique activée
: le passage devant les cellules provoque
la fermeture immédiate du portail.
impact contre un
obstacle
1
23
4
ON
SW
1
Détection d’obstacle activée
: l’impact contre un obstacle, aussi bien en phase
d’ouverture que de fermeture, est détecté par le système à encodeur qui bloque le
portail et inverse le mouvement de 10 cm -voir page 5-
12
3
4
ON
SW
1
Détection d’obstacle désactivée
: l’impact contre un obstacle n’est pas détecté et
le moteur continue à pousser.
Si la détection d’obstacle est désactivée, adopter d’autres systèmes de
sécurité (ex : barre palpeuse) conformément aux normes en vigueur.
La responsabilité de l’installation d’automatisation et de son
fonctionnement «selon les normes» incombe à l’installateur.
active/désactive
préavis feu orange
12
3
4
ON
SW
1
préavis désactivé
: le feu orange s’allume simultanément à l’ouverture du portail.
123
4
ON
SW1
préavis activé
: le feu orange s’allume 3 secondes avant l’ouverture du portail.
mode de
fonctionnement
12
3
4
ON
SW
1
mode séquentiel : 4 pas
Durant l’ouverture : l’envoi d’une commande ouvre/ferme provoque l’arrêt du
mouvement, une commande successive provoque la fermeture du portail.
Durant la fermeture : l’envoi d’une commande ouvre/ferme provoque l’arrêt du
mouvement, une commande successive provoque l’ouverture du portail.
Durant la pause portail ouvert : une commande ouvre/ferme annule le temps de
pause et provoque la fermeture immédiate du portail.
1
2
3
4
ON
SW1
mode semi-automatique : 3 pas
Durant l’ouverture
: l’envoi d’une commande ouvre/ferme est ignorée, le portail
continue à s’ouvrir.
Durant la fermeture : l’envoi d’une commande ouvre/ferme bloque le portail pendant
quelques secondes puis il se réouvre.
Durant la pause portail ouvert : une commande ouvre/ferme annule le temps de
pause et provoque la fermeture immédiate du portail.
ne paS utiliSeR
1
2
3
4
ON
SW
1
laisser en position oFF.
9.1. paramétrage des modes de
fonctionnement
Le paramétrage des fonctionnements s’effectue avec les
micro-interrupteurs SW1 et SW2.
Pendant les opérations de paramétrage, le moteur doit être hors tension.
En cas de modification des paramètres, il faut éteindre et rallumer l’unité de commande pour rendre actif ces
nouveaux paramètres.
O
LAVOR
PAUSA
PROG
PROG
+
-
RE
G
10
9
18
19
20
21
22
START
PED
STOP
FOTO
FCA
FCC
COSTA
DL10
DL11
ENCODER
DL12
1
2
3
4
5
6
7
8
SOG/4
A
F1
F2
O
LAVOR
AA
PAUSA
PROG
PROG
+
-
R
EG
21
22
START
PED
STOP
FOTO
FCA
FCC
COSTA
DL10
DL11
EN
C
O
D
ER
DL12
2
SO
G
/4
A
F1
F2
1
3
4
5
6
7
8
10
9
19
20
18
SW1
SW2
O
N
O
N