Somat SPC-50S Operation Manual Download Page 16 | Manualshive

Page: 16 / 52

background image

16

MECHANICAL INSTALLATION

HIGH TANK MODELS:
1.

Put the pulper/extractor into position as shown on the Installation Drawings.

2.

Place the Anti-Vibration Pads under each leg of the Pulper and Hydra-Extractor

®

. *

3.

TRAY FEED UNITS ONLY - Install the tray to the Pulper (if it was not already installed

at the factory) using the provided gasket material and hardware.

4.

TROUGH FEED UNITS ONLY - Install the provided trough gasket between the Pulpers

inlet and the trough outlet and secure with the provided hardware.

*

«
...
14
15
16
17
18
...
»

Summary of Contents for SPC-50S





















































Reviews:

No comments

Related manuals for SPC-50S

Brand: OMCA Pages: 36

Brand: Salford Pages: 64

SATURA SPOT LED PRO

Brand: Elation Pages: 41

Brand: Tapco Pages: 16

Brand: Zenbooth Pages: 40

Visium CytAssist

Brand: 10x Genomics Pages: 51

Chromium X Series

Brand: 10x Genomics Pages: 5

Brand: ParaBody Pages: 6

Brand: Sailmon Pages: 10

Brand: B&W Tek Pages: 12

Brand: b&o Pages: 46

Brand: d.s.f. Pages: 8

ST60+ SPEED INSTRUMENT

Brand: Raymarine Pages: 60

Brand: Raymarine Pages: 15

Brand: RaycoWylie Pages: 9

Brand: Raven Pages: 58

Brand: Raven Pages: 26

Brand: Ravo Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands