Sollae Systems CIE-H10A Page 76 User Manual Download

Page: 76 / 80

CIE-H10A User Manual Ver. 1.1

- 75 -

https://www.ezTCP.com

Precaution and Exemption from Liability

12.1

Precaution

⚫

Sollae Systems is not responsible for product failures occurring due to user

’

alternation of the product.

⚫

Specifications of the product are subject to change without prior notice for
performance improvement.

⚫

Sollae Systems does not guarantee successful operation of the product if the
product was used under conditions deviating from the product specifications.

⚫

Reverse engineering of firmware and applications provided by Sollae Systems is
prohibited.

⚫

Use of firmware and applications provided by Sollae Systems for purposes other
than those for which they were designed is prohibited.

⚫

Do not use the product in an extremely cold or hot place or in a place where
vibration is severe.

⚫

Do not use the product in an environment in which humidity is high or a lot of oil
exists.

⚫

Do not use the product where there is caustic or combustible gas.

⚫

Sollae Systems does not guarantee normal operation of the product under the
conditions a lot of noise exists.

⚫

Do not use the product for a purpose that requires exceptional quality and
reliability relating to user

’

s injuries or accidents

–

aerospace, aviation, health care,

nuclear power, transportation, and safety purposes.

⚫

Sollae Systems is not responsible for any accident or damage occurring while using
the product.

Summary of Contents for CIE-H10A

















































































Search results

Summary of Contents for CIE-H10A

Reviews:

Related manuals for CIE-H10A

Brands by name

Popular brands

Sollae Systems CIE-H10A, User Manual

Search results

Summary of Contents for CIE-H10A

Reviews:

Related manuals for CIE-H10A

Brands by name

Popular brands