Sollae Systems CIE-H10A Page 45 User Manual Download

Page: 45 / 80

CIE-H10A User Manual Ver. 1.1

- 44 -

https://www.ezTCP.com

⚫

TCP Server
This check option is enable the TCP server / client mode. In this mode, CIE-H10A can
be operated as a TCP server or client without changing its setting.

⚫

DNS IP Address
[DNS IP Address] is required when users use a host name instead of the IP address
on the [Peer Port] parameter.

6.2.2

Examples

⚫

A situation that [Event Byte] is set to 0

Figure 6-4 time chart

Time

States

Power is not supplied yet.

①

CIE-H10A sends a connection request segment right after it
boots up.

processes of TCP connection

②

The connection is established.

data communication on both sides

Table 6-7 states of each point

Look at the blue arrow. The data

“

123

”

from the serial port was sent before establishing

a connection. In this case, the data would not be sent because of the [Event Byte] is set to
0.

Summary of Contents for CIE-H10A

















































































Search results

Summary of Contents for CIE-H10A

Reviews:

Related manuals for CIE-H10A

Brands by name

Popular brands

Sollae Systems CIE-H10A, User Manual

Search results

Summary of Contents for CIE-H10A

Reviews:

Related manuals for CIE-H10A

Brands by name

Popular brands