SOLAC Siphon Brewer 3-in-1, Instructions For Use Manual, Page: 6 / 25

ES
EN
(Original instructions)
•
8. Rinse the siphon tube with cold water in or-
der to cool off, then you can remove it from the
lid.
•
9. Place the jar lid over the jar aligning the “UN-
LOCK” line with the handle´s mark, turn the lid
clockwise until “POUR” line match with the
mark of the handle and pour.
•
¡CAUTION! PLACE THE LID OVER THE JAR
BEFORE SERVING
WATER BOILER MODE
•
1. Fill up the jar with room temperature drinking
water above the minimum level of 21.12 oz.
(0.6 l) but below the maximum level of 23.67
oz. (0.7 l). Make sure the siphon tube is not set
inside the jar.
•
2. Following the jar lid marks, set over the jar
by aligning the “UNLOCK” line with the mark
of the handle, then turn lightly clockwise until
the “BOIL” line match up with the center of the
handle.
•
3. Set it up over the heating plaque, plug it to
the power source and press on/ off button just
once the red light will turn on.
•
4. When the water starts to boil the applian-
ce will start to whistle, then you can turn your
appliance off by pushing the on/off button once
and the red light will turn off. Unplug and re-
move the jar from the heating plaque holding it
by its handle. In case the water entirely evapo-
rates the appliance will turn off automatically.
•
5. Carefully turn the lid clockwise until the
“POUR” line matches with the center of the
handle and you can actually see the dispenser
in order to pour.
•
¡CAUTION! PLACE THE LID OVER THE JAR
BEFORE SERVING
TEA MODE (INFUSIONS)
•
1. Fill up the jar with room temperature drinking
water above the minimum level of 21.12 oz.
(0.6 L) but below the maximum level of 28.16
oz. (0.8 L).
•
2. Set the siphon tube inside the jar, with the
circular part facing up and lining it up along
with the jar gaps, afterwards turn the tube cloc-
kwise until it sets.
•
3. Above the jar, set the upper vessel lining its
mark up with the handle’s line. Then turn the
upper vessel by its handle, clockwise until both
handles match.
•
4. Put inside the upper vessel the mesh filter
handling it by its insulating handle and make
the flanges of the mesh filter align with the
upper vessel gaps, finally turn the mesh filter
clockwise until it adjust.
•
5. Put your choice of infusion in (maximum
quantity 1.76 oz. or 50 g), according the
amount of water with which you filled up the jar
and then close the lid of upper vessel.
•
Place the appliance over the heating plaque
then plug to the power source and turn on pus-
hing the on/off button, a red light will turn on. If
you push twice the on/off button the appliance
will perform two infusion cycles (the red light
will start flashing). You can do so whether you
would like your infusion stronger, however you
must leave the two cycles to reach the end be-
fore you open or manipulate any part of your
appliance (refer to “double cycle” text at coffee
mode instructions).
•
7. Once the water reaches the perfect tempe-
rature, in about 5 minutes, the water will rai-
se through the siphon tube all the way up to
the upper vessel, once the programmed time
ends, about 1 more minute, the water will des-
cend down suddenly to the jar, this means your
beverage is ready!. These times are those of
one infusion cycle if you choose two cycles,
you will experience twice the process, before
pouring your beverage.
•
8. Once the cycle ends (either 1 or 2), verify
the red light is off, unplug your appliance and
remove it from the heating plaque holding it
from its handle.
•
9. Separate the upper vessel from the jar. To
remove the siphon tube use the jar lid and align
the gaps of the lid with the flanges of the siphon
tube (for reference, match the “POUR” line with
the handle´s mark) and firmly press down in
order to match the flanges into the gaps, then
turn counter clockwise until the siphon tube
releases from the jar and raise the lid to take
the tube out. DO NOT REMOVE THE SIPHON
TUBE WITH YOUR BARE HANDS!