Sofar solar HYD 10KTL-3PH User Manual Download Page 104

Page: 104 / 118

HYD 5-20KTL-3PH

User manual

- 99 -

ID036

MChip_Fault

Chip error (AC)

ID037

AuxPowerFault

Auxiliary power error

ID038

InvSoftStartFail

Inverter failed to output

ID041

RelayFail

Relay detection failure

ID042

IsoFault

Low insulation

impedance

Check the insulation resistance between the

photovoltaic array and ground (ground), if

there is a short circuit, the fault should be

repaired in time.

ID043

PEConnectFault

Ground fault

Check ac output PE wire for grounding.

ID044

InputConfigError

Error setting input

mode

Check the input mode (parallel/independent

mode) Settings for the inverter. If not,

change the input mode.

ID045

CTDisconnect

CT error

Check whether the CT wiring is correct.

ID046

Reversal Connect

The battery is

connected reversedly

Check whether the battery wiring is correct.

ID047

Parallel Fault

Master does not exist or

is duplicate

Check the parallel mode settings for the

inverter. Check whether the wiring is

correct.

ID048

SNTypeFault

Serial number fault

Internal faults of inverter, switch OFF

inverter, wait for 5 minutes, then switch ON

inverter. Check whether the problem is

solved.

If no, please contact technical support.

ID049

TempFault_Bat

Battery temperature

protection

For Inner BMS battery, make sure that the

battery NTC cable is properly connected.

Make sure the inverter is installed where

there is no direct sunlight.

Please ensure that the inverter is installed in

a cool/well ventilated place.

Ensure the inverter is installed vertically

and the ambient temperature is below the

inverter temper ature limit.

ID050

TemFaultRadiat1

Radiator 1 temperature

protection

ID057

TemFaultEnv1

Ambient temperature 1

protection

ID059

TemFaultInv1

Module 1 temperature

protection

ID065

VbusRmsUnbala

Unbalanced bus voltage

RMS

Internal faults of inverter, switch OFF

inverter, wait for 5 minutes, then switch ON

inverter. Check whether the problem is

solved.

If no, please contact technical support.

ID066

VbusInstUnbalan

The transient value of

bus voltage is

unbalanced

ID067

BusUVP

Busbar undervoltage

during grid-connection

ID068

BusZVP

Bus voltage low

ID069

PVOVP

PV over-voltage

Check whether the PV series voltage (Voc)

is higher than the maximum input voltage

of the inverter. If so, adjust the number of

PV modules in series and reduce the PV

series voltage to fit the input voltage range

of the inverter. After correction, the inverter

will automatically return to its normal state.

ID070

BatOVP

Battery over-voltage

Check whether the battery overvoltage

Summary of Contents for HYD 10KTL-3PH























































































































Search results

Summary of Contents for HYD 10KTL-3PH

Reviews:

Related manuals for HYD 10KTL-3PH

Brands by name

Popular brands

Sofar solar HYD 10KTL-3PH, User Manual

Search results

Summary of Contents for HYD 10KTL-3PH

Reviews:

Related manuals for HYD 10KTL-3PH

Brands by name

Popular brands