Grill Assembly
Step 16:
Procedure: Refer to Fig. 16 and set the HVR
Cover in the front corner of the Gas Grill Cabinet,
so that it covers the actual HVR where it
enters and exits the Cabinet. Fasten in place
with (2) M6x15 bolts.
Note: Be sure top of cover is positioned under the
Rivnut as shown.
Step 17:
Procedure: Attached to each Burner Tube is
an Ignition Electrode with a pin at the end of
the Electrode. You need to attach each of the
(3) ignition wires that you had pushed through
the openings onto the pin end of the Electrode
per Fig. 17A.
Refer to Fig. 17B and Fig 17C. Tilt the burner
tube slightly and insert through the opening in
the front wall of the cabinet. You MUST make
certain that the tip of the valve is completely
INSIDE the end opening of the Burner Tube.
After each Burner Tube is set in place at the
front of the Cabinet, you must fasten the
Burner Tube to the Burner Support Brackets
at the back of the cabinet with (3) ST4.0x10
screw per Fig. 17D.
Assembly
Step 17: Assemble the Burner Tubes to
the Grill
Locate:
(3) Burner Tubes with Igniter elec-
trodes attached and (3) ST4.0x10 Screws.
Procedure
: Attached to each Burner Tube is
an Ignition Electrode with a pin at the end of
the Electrode. You need to attach each of the
(3) ignition wires that you had pushed through
the openings onto the pin end of the Electrode
per Fig. 17A.
Refer to Fig. 17B and Fig 17C. Tilt the burner
tube slightly and insert through the opening in
the front wall of the cabinet. You
MUST
make
certain that the tip of the valve is completely
INSIDE
the end opening of the Burner Tube.
After each Burner Tube is set in place at the
front of the Cabinet, you must fasten the
Burner Tube to the Burner Support Brackets
at the back of the cabinet with (3) ST4.0x10
screw per Fig. 17D.
Step 16
:
Assemble the HVR Cover
Locate
: HVR Cover and (2) M6x15 bolts
Procedure
: Refer to Fig. 16 and set the HVR
Cover in the front corner of the Gas Grill Cabi-
net, so that it covers the actual HVR where it
enters and exits the Cabinet. Fasten in place
with (2) M6x15 bolts.
Be sure top of cover is positioned under the
Rivnut as shown.
Rivnut
16
Assembly
Step 17: Assemble the Burner Tubes to
the Grill
Locate:
(3) Burner Tubes with Igniter elec-
trodes attached and (3) ST4.0x10 Screws.
Procedure
: Attached to each Burner Tube is
an Ignition Electrode with a pin at the end of
the Electrode. You need to attach each of the
(3) ignition wires that you had pushed through
the openings onto the pin end of the Electrode
per Fig. 17A.
Refer to Fig. 17B and Fig 17C. Tilt the burner
tube slightly and insert through the opening in
the front wall of the cabinet. You
MUST
make
certain that the tip of the valve is completely
INSIDE
the end opening of the Burner Tube.
After each Burner Tube is set in place at the
front of the Cabinet, you must fasten the
Burner Tube to the Burner Support Brackets
at the back of the cabinet with (3) ST4.0x10
screw per Fig. 17D.
Step 16
:
Assemble the HVR Cover
Locate
: HVR Cover and (2) M6x15 bolts
Procedure
: Refer to Fig. 16 and set the HVR
Cover in the front corner of the Gas Grill Cabi-
net, so that it covers the actual HVR where it
enters and exits the Cabinet. Fasten in place
with (2) M6x15 bolts.
Be sure top of cover is positioned under the
Rivnut as shown.
Rivnut
16
Assembly
Step 17: Assemble the Burner Tubes to
the Grill
Locate:
(3) Burner Tubes with Igniter elec-
trodes attached and (3) ST4.0x10 Screws.
Procedure
: Attached to each Burner Tube is
an Ignition Electrode with a pin at the end of
the Electrode. You need to attach each of the
(3) ignition wires that you had pushed through
the openings onto the pin end of the Electrode
per Fig. 17A.
Refer to Fig. 17B and Fig 17C. Tilt the burner
tube slightly and insert through the opening in
the front wall of the cabinet. You
MUST
make
certain that the tip of the valve is completely
INSIDE
the end opening of the Burner Tube.
After each Burner Tube is set in place at the
front of the Cabinet, you must fasten the
Burner Tube to the Burner Support Brackets
at the back of the cabinet with (3) ST4.0x10
screw per Fig. 17D.
Step 16
:
Assemble the HVR Cover
Locate
: HVR Cover and (2) M6x15 bolts
Procedure
: Refer to Fig. 16 and set the HVR
Cover in the front corner of the Gas Grill Cabi-
net, so that it covers the actual HVR where it
enters and exits the Cabinet. Fasten in place
with (2) M6x15 bolts.
Be sure top of cover is positioned under the
Rivnut as shown.
Rivnut
16
Assembly
Step 17: Assemble the Burner Tubes to
the Grill
Locate:
(3) Burner Tubes with Igniter elec-
trodes attached and (3) ST4.0x10 Screws.
Procedure
: Attached to each Burner Tube is
an Ignition Electrode with a pin at the end of
the Electrode. You need to attach each of the
(3) ignition wires that you had pushed through
the openings onto the pin end of the Electrode
per Fig. 17A.
Refer to Fig. 17B and Fig 17C. Tilt the burner
tube slightly and insert through the opening in
the front wall of the cabinet. You
MUST
make
certain that the tip of the valve is completely
INSIDE
the end opening of the Burner Tube.
After each Burner Tube is set in place at the
front of the Cabinet, you must fasten the
Burner Tube to the Burner Support Brackets
at the back of the cabinet with (3) ST4.0x10
screw per Fig. 17D.
Step 16
:
Assemble the HVR Cover
Locate
: HVR Cover and (2) M6x15 bolts
Procedure
: Refer to Fig. 16 and set the HVR
Cover in the front corner of the Gas Grill Cabi-
net, so that it covers the actual HVR where it
enters and exits the Cabinet. Fasten in place
with (2) M6x15 bolts.
Be sure top of cover is positioned under the
Rivnut as shown.
Rivnut
16
Assembly
Step 17: Assemble the Burner Tubes to
the Grill
Locate:
(3) Burner Tubes with Igniter elec-
trodes attached and (3) ST4.0x10 Screws.
Procedure
: Attached to each Burner Tube is
an Ignition Electrode with a pin at the end of
the Electrode. You need to attach each of the
(3) ignition wires that you had pushed through
the openings onto the pin end of the Electrode
per Fig. 17A.
Refer to Fig. 17B and Fig 17C. Tilt the burner
tube slightly and insert through the opening in
the front wall of the cabinet. You
MUST
make
certain that the tip of the valve is completely
INSIDE
the end opening of the Burner Tube.
After each Burner Tube is set in place at the
front of the Cabinet, you must fasten the
Burner Tube to the Burner Support Brackets
at the back of the cabinet with (3) ST4.0x10
screw per Fig. 17D.
Step 16
:
Assemble the HVR Cover
Locate
: HVR Cover and (2) M6x15 bolts
Procedure
: Refer to Fig. 16 and set the HVR
Cover in the front corner of the Gas Grill Cabi-
net, so that it covers the actual HVR where it
enters and exits the Cabinet. Fasten in place
with (2) M6x15 bolts.
Be sure top of cover is positioned under the
Rivnut as shown.
Rivnut
16
Fig. 16
Fig. 17A
Fig. 17B
Fig. 17C
Fig. 17D
14
