background image

MODEL GT SERIES

INSTALLATION, OPERATING 

AND MAINTENANCE MANUAL

Modulating, Direct Vent, Gas-Fired Condensing Boilers

Natural Or Propane 

150,000 to 200,000 Btuh Input

GTIOM-2

gama

ENERGY STAR

ENERGY STAR

Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of 
this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
•  Do not try to light any appliance.
•  Do not touch any electrical switch. Do not use any phone in your building.
•  Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s 

instructions.

•  If you cannot reach your gas supplier, call the fi re department.
Installation and service must be performed by a qualifi ed installer, service agency or 
the gas supplier.

WARNING: If the information in this manual is not followed exactly, a fi re or explosion 
may result causing property damage, personal injury or loss of life.

INSTALLER: THESE INSTRUCTIONS MUST BE AFFIXED ADJACENT TO THE BOILER.

CONSUMER: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE PURPOSES.

Note: ASME on the GT-200 only

WARNING: Installation and service must be performed by a qualifi ed installer, service 
agency or the gas supplier in accordance with all local and national codes.  Failure to 
comply with this warning can result in a fi re or explosion causing property damage, 
personal injury or loss of life!
 

      

WARNING: It is the responsibility of the homeowner to keep the vent terminal clear 
of snow and ice. Failure to comply with this warning can result in excessive levels of 
carbon monoxide causing severe personal injury or death!

see note

 WESTCAST, 

INC. 

 

260 NORTH ELM STREET WESTFIELD, MA 01085  

 

TEL. (413) 562-9631  FAX (413) 562-3799

Summary of Contents for GT-150









































Reviews: