9
EN
Description of the milk container
(page 3 - D)
D1. Froth adjustment and CLEAN function dial
D2 Lid with milk frother
D3. Milk container
D4. Milk intake tube
D5. Adjustable frothed milk spout
D6. Thermal casing
D7. Lid release buttons
PRELIMINARY OPERATIONS
Checking the appliance
After removing the packaging, make sure the product is com-
plete and undamaged and that all accessories are present. Do
not use the appliance if it is visibly damaged. Contact customer
services Technical Assistance.
SETTING UP THE APPLIANCE
Please note:
• Coffee has been used to factory test the appliance and it is
therefore completely normal to find traces of coffee in the
mill. The machine is, however, guaranteed to be new.
• You should customise water hardness as soon as possible
following the instructions in section “Setting water hard-
ness”.
1. Connect the appliance to the mains electricity supply
(fig. 1) and make sure the main switch (A19) on the side of
the appliance is pressed down (fig. 2);
2. SELECT LANGUAGE (setting language): press
(B10) or
(B8) until the flag corresponding to the required lan-
guage appears on the display (B), then press the flag;
To proceed follow the instructions indicated on the appliance
display:
1. FILL WATER TANK WITH FRESH WATER: remove the water
tank (A12) (fig. 3), open the lid (fig. 4), fill to the MAX line
(marked on the inside of the tank) with fresh water (fig. 5);
close the lid and put the tank back into the appliance
(fig. 6);
2. INSERT WATER OUTLET: Check that the hot water/steam
spout (C6) is inserted on the connection nozzle (A10)
(fig. 7) and place a container with a minimum capacity of
100 ml underneath (fig. 8);
3. WATER CIRCUIT EMPTY PRESS OK TO START FILLING PRO-
CESS is shown on the display;
4. Press
to confirm: the appliance delivers water from
the spout (fig. 8) then goes off automatically.
The coffee machine is now ready for normal use.
Please note:
• The first time the appliance is used, it needs to make 4-5
cappuccinos before it starts to give satisfactory results.
• On first use the water circuit is empty, the machine could
therefore be very noisy: the noise will lessen as the circuit
fills up.
• When making the first 5-6 cappuccinos, it is normal to hear
the noise of boiling water: after this the noise will lessen.
• To improve the performance of the appliance, we recom-
mend installing a water softener filter (C4) as described in
section “Water softener filter”. If your model is not equipped
with a filter, it is possible to request one from Authorised
Customer Service Centres.
TURNING THE APPLIANCE ON
Please note:
Before turning the appliance on, make sure the main switch
(A23) is pressed (fig. 2). Each time the appliance is turned on, it
performs an automatic preheat and rinse cycle which cannot be
interrupted. The appliance is ready for use only after completion
of this cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
(A13) and is collected in the drip tray (A14) underneath. Avoid
contact with splashes of water.
• To switch the appliance on, press the button
(A7-
fig. 9): message HEATING UP PLEASE WAIT, is shown on the
display.
• When heating is complete, the message changes to: RINS-
ING HOT WATER RUNNING; As well as heating the boiler, the
appliance also continues to allow hot water to run in the
internal pipework as they also heat up.
The appliance is at the desired temperature when the main
screen, homepage, appears.
TURNING THE APPLIANCE OFF
Every time the appliance is turned off, it automatically carries
out a rinse if it has made a coffee.
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts
(A13). Avoid contact with splashes of water.
• To turn the appliance off, press the button
(A7-fig. 9).
• The message TURNING OFF PLEASE WAIT is shown on the
display: if needed the appliance performs a rinse cycle and
then goes off (standby).
